PT100 Auto Parts Test Equipment IEC60068 Three Box Cold And Hot Impact Tester
hree-Box Cold And Hot Impact Tester Auto Parts Test Equipment IEC60068
Products Introduction:
The hot and cold impact test machine is to test whether the product has a bad impact due to the rapid changes of high and low temperature without moving the items to be tested. It is a necessary test equipment for metal, plastic, rubber, electrical and electronics, auto parts and other material industry.Auto Parts Test Equipment
Meet the standards:
GJB 150.4-1986 low temperature test;Auto Parts Test Equipment
GJB 150.3-1986 high temperature test;
GJB 150.5-1986 temperature impact test;
GB / T 5170.2-1996 temperature test equipment;
GB / T 2423.1-2001(IEC60068-2-1:1990) test A: Low temperature test method;
GB / T 2423.2-2001(IEC60068-2-2:1974) test B: High temperature test method;
GB / T 2423.22-2002 (IEC60068-2-14:1984) test N: Temperature change test method test Na.
Three-box hot and cold impact technical indicators:
| Model | AM0036-LC64 | AM0036-LC100 | AM0036-LC150 | AM0036-LC200 |
| Inner box size mm (W * H * D) | 400×400×400 | 500×450×450 | 600×500×500 | 650×460×670 |
| Outline dimension mm (W * H * D) | 1440×1910×1825 | 1520×1990×2050 | 1620×2040×2100 | 1620×1980×2140 |
| Temperature impact range | A:-40～+150℃, B:-55～+150℃, C:-65～+150℃ | |||
| Cold storage temperature range in the low temperature area | -10℃～-50℃； -10℃～-65℃； -10℃～-75℃ | |||
| Heat storage temperature range in the high temperature area | +50℃～+180℃ | |||
| Impact reinstatement time | About 5min | |||
| High and low temperature impact constant temperature time | 30min more than | |||
| High temperature setting | +60℃ ～ +150℃ | |||
| Low temperature setting | -65℃ ～ -10℃ | |||
| Temperature fluctuation in the sample zone | ± 0.5℃ (at constant temperature) | |||
| Temperature accuracy range | Set accuracy: ± 0.1℃, indicating accuracy: ± 0.1℃, resolution: ± 0.1℃ | |||
| Temperature deviation | ± 2℃ (no-load, at constant state) | |||
| Temperature sensor | High-precision Class A PT100 | |||
| Cryogen | R404a,R23 Auto Parts Test Equipment | |||
| Box structure | With an independent product test area, high temperature heat storage area, low temperature cold storage area | |||
| Internal box material | SUS304 stainless steel plate | |||
| Outer box material | Cold tie plate baking paint | |||
| Insulation material | Hard polyurethane foam + insulation cotton | |||
| Round-robin mode | Multi-blade fan | |||
| Heater | Nickel-branded alloy electric heater | |||
| condensator | Shell-tube-type condenser (water-cooled type) | |||
| Evaporator | High performance fin type automatic load capacity adjustment, long-term use of low temperature and high humidity conditions without frosting | |||
| Controller | The 7-inch color LCD touch control screen + PLC module | |||
| Program capacity |
Available program capacity: maximum 120 groups; each section time setting: 99 hours 59 points; Auto Parts Test Equipment |
|||
| Service rating | About 9~30KW (auto-on heating and cooling based on PID operation) | |||
| Supply source | 380V ± 10%V; 50Hz; three-phase four-wire + grounding wire, protective grounding resistance is less than 4 Ω | |||
| Safety device |
Ultra-temperature protection, motor overload protection, compressor high voltage protection switch, compressor overheat protection switch, compressor overcurrent protection, overvoltage underphase phase protection switch, leakage circuit breaker, cooling water abnormal protection. |
|||
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.