Auto Parts Test Equipment

Auto Parts Test Equipment Safety Test System For Electrically Vehicle Standard: ISO 6469-1 Electrically propelled road vehicles-Safety specifications-Part1: On-board rechargeable energy storage system (REESS) GB/T 18384.1 Electrically propelled road vehicles-Safety specifications-Part1: On-board rechargeable energy storage system (REESS) GB/T 18487.1 Electric vehicle conductive charging system-Part 1: General requirements GB/T 20234.1 Connection set for conductive charging of

Auto Parts Test Equipment Leak Test for EV Battery Cells With 1 Vacuum Chamber Leak Test for EV Battery Cells Equipment basic function: This equipment is a vacuum chamber helium leak detection system for the steel-cased battery cell, which mainly contains the processes of battery code scan, loading, evacuation, helium filling, helium leak inspection, and unloading. Then the helium signal in the leak detection chamber is detected by the helium leak detector, which can

Auto Parts Test Equipment ISO 16750 Ice Water Shock Test For Electronic Components Standard: VW-80000 Electric And Electronic Components In Motor Vehicles up to 3.5t General Requirements, Test Conditions and Tests clause 9.12 K-12 Temperature Shock With Splash Water; ISO16750-4 Road vehicles-Environmental conditions and testing for electrical and electronic equipment-Part 4: Climatic loads clause 5.4.2 Ice water shock test. Purpose: This test simulates a thermal shock induced

Auto Part Test Equipment Anti-Rust And Antifreeze Vacuum Filling Machine Basic Function: Connect the filling gun on the filling equipment to the filling port of the water tank, start the equipment work switch, and the equipment will automatically vacuumize the cooling pipeline and fill the rust and antifreeze fluid. The filling gun adopts the dual-channel design of the evacuation channel and the anti-rust and antifreeze channel. The main water tank filling volume is

Auto Parts Test Equipment Performance Test System Of Automobile Alternator Product information: The automobile alternator comprehensive performance test system (referred to as the one-to-two experiment platform) can drive two motors at the same time for testing. It is mainly used for the comprehensive test of high-speed impact (rapid shifting), high and low temperature and humidity durability of the alternator to simulate automobile AC Testing equipment for the working status

Cleanliness Tester Auto Parts Test Equipment ISO 16232 / VDA19 defines the particle properties Products Introduction: The Cleanliness Expert is a precision-designed component cleaning analysis system that detects the residual particles of the filter paper and, most importantly, enables a reliable and reproducibility evaluation of the artifact cleanliness.Auto Parts Test Equipment Standard: ISO 16232 / VDA19 defines the particle properties ISO 16232 / VDA19 resolution

ISO 16750-4 Auto Parts Test Equipment Splash Water And Submersion Test Chamber Standard: ISO16750-4 Road vehicles-Environmental conditions and testing for electrical and electronic equipment-Part 4: Climatic loads, clause 5.4.2 Ice water shock test. VW-80000 Electric And Electronic Components In Motor Vehicles up to 3.5t General Requirements, Test Conditions and Tests clause 9.12 K-12 Temperature Shock With Splash Water; GB/T 28046.4-2011 Auto Parts Test Equipment Purpose:

Auto Parts Test Equipment Car Air-Conditioning Refrigerant Vacuum Filling Machine Work process description: After the filling gun is connected to the workpiece, press the start switch, and the filling machine will automatically vacuum the workpiece. When the workpiece reaches the set vacuum, the equipment will perform vacuum pressure-holding and leak detection on the workpiece; if the workpiece is found to be leaking, the equipment will automatically stop the charging

Vehicle Test Equipment IPX8 Pressure Immersion Test Device 500mm Diameter Standard: IEC60529 degree of protection provided by enclosures (IP Code) of the IP8; ISO 20653-2013 Road vehicles — Degrees of protection (IP code) — Protection of electrical equipment against foreign objects, water and access Degrees of protection against water Second code element 8; Brief description: Continuous immersion in water: Water shall not penetrate in a quantity causing harmful effects if the

Auto Parts Test Equipment Mechanical Shock Test Machine For Auto Parts Accessories Standard: This part of ISO 12405 specifies test procedures for lithium-ion battery packs and systems for use in electrically propelled road vehicles; ISO 16750-3 Road vehicles — Environmental conditions and testing for electrical and electronic equipment — Part 3: Mechanical loads; IEC 60068-2-27 Environmental testing – Part 2-27: Tests – Test Ea and guidance: Shock Application: Shock test is

Auto Parts Test Equipment ISO12405-1 3 Axis Vibration Test For Vehicles Battery Packs Standard: ISO12405-1 Electrically propelled road vehicles — Test specification for lithium-ion traction battery packs and systems — Part 1: High-power applications Applications: This part of ISO 12405 specifies test procedures for lithium-ion battery packs and systems for use in electrically propelled road vehicles. Auto Parts Test Equipment The specified test procedures enable the

Automobile Water Tank Expansion Blasting Testing Machine 0-300Mpa Auto Parts Test Equipment Products Introduction: Automobile water tank expansion blasting testing machine ,Pulse pump generates pressure, pressure sensor collects pressure, operating software controls pressure, pressure pulse fatigue test is realized.Auto Parts Test Equipment Scope of application: Automobile expansion water tank, pressure water tank, gas storage tank.Auto Parts Test Equipment Test sample:

hree-Box Cold And Hot Impact Tester Auto Parts Test Equipment IEC60068 Products Introduction: The hot and cold impact test machine is to test whether the product has a bad impact due to the rapid changes of high and low temperature without moving the items to be tested. It is a necessary test equipment for metal, plastic, rubber, electrical and electronics, auto parts and other material industry.Auto Parts Test Equipment Meet the standards: GJB 150.4-1986 low temperature test

Air tightness detector 1pa-200pa 1-800kpa Auto Parts Test Equipment Products Introduction:Auto Parts Test Equipment Instrument belongs to a type of key operation, set up the test parameters to press the start button after the instrument is up and running, automatic monitoring of product testing, testing process can be real-time monitoring on the instrument interface testing, testing after the completion of the indicator light for "OK" or "NG" will light up lights, test

IPX1-1PX8 Test System For Degrees of Protection Against Water Auto Parts Test Equipment Standard: ISO 20653-2013 Road vehicles — Degrees of protection (IP code) — Protection of electrical equipment against foreign objects, water and access, figure 3, figure 4, figure 5 and figure 6 and table 7; IEC60529 degree of protection provided by enclosures (IP Code), clause 14.2.1, 14.2.2, 14.2.3, 14.2.4, 14.2.5, 14.2.6, 14.2.7, 14.2.8, and figure 3, figure 4, figure 5 and figure 6,

Car Refrigerant R22 Filling Machine Auto Parts Test Equipment 150g/s Speed Specification: Amount of injection 200-99999g Inject refrigerant R22 or R410a System vacuum degree 20Pa Injection speed 150g/s Injection accuracy Filling volume ≤500 g, ±1%; filling volume>500g, ±0.5% Working process: After the filling gun is connected to the workpiece, press the start switch, and the filling machine will automatically vacuum the workpiece. When the workpiece reaches the set vacuum,

Auto Part Test Equipment Tensile And Elongation Strength Measuring Device Product information: This tensile and elongation machine is conforms to ISO, JIS, ASTM, DIN and other relevant standards. It is suitable for all kinds of food packaging, textile, rubber, plastic, synthetic leather, tape, electronics, metal and other industries, such as materials and products to do tensile, peeling, tearing and other tests to determine the quality of the product. The machine is driven by

Auto Parts Test Equipment Rapid Change Of High/Low Temperature Chamber (Wet And Hot) Standard: IEC 60068-2-1 Environmental testing for electric and electronic products – Part 2-1: Tests methods – Test A: Cold; IEC 60068-2-2 Environmental testing for electric and electronic products – Part 2-2: Tests methods – Test B: Dry heat; IEC 60068-2-78 Environmental testing – Part 2-78: Tests methods – Test Cab: Damp heat, steady state; IEC 60068-2-30 Environmental testing for electric

Auto Parts Test Equipment Waterproof Tests Chamber For IPX1 To IPX4 Standard: IEC60529 degree of protection provided by enclosures (IP Code) of the IPX1, IPX2, IPX3, IPX4; DIN40050-9 IP degrees of protection provided by enclosures for the electrical equipment in road vehicles for protecting the electrical equipment inside the enclosure against the effects of the ingress of solid foreign objects, including dust (protection against foreign objects),protecting the electrical

Rapid Temperature Change Test Chamber 20%〜98%RH Auto Parts Test Equipment IEC68 Products Introduction: It is suitable to conduct high and low temperature ,wet and heat tests for electricians, electronics, machinery and other products, parts, materials, and to conduct quality and reliability tests for products, parts and materials under simulated temperature and humidity changes.Auto Parts Test Equipment Meet the standards: GJBl50.9-2009 (MIL-STD-810D) Hot and heat test method