Salt Evaporator Vane Pack Mist Eliminator 2205 Stainless Steel 20mm Vane Pitch
Salt Evaporator Use Vane Pack Mist Eliminator 2205 Material
Blade assembly defogger working process:
When the fogged gas passes through the blade group defogger at a certain speed, the fog collides with the wave plate and adheres to the surface of the wave plate due to the inertial impact of the gas. The multiple folding structure of the wave plate of the defogger increases the chance of collecting fog. The uncollected fog will work repeatedly through the same function in the next round of catching, thus greatly improving the efficiency of the defogger. After the gas passes through the V-shaped defogger, there is basically no fog.
Blade assembly defogger structure:
The blade assembly defogger consists of a set of V-shaped corrugated plates with a well-defined geometry. It is very popular and useful in gas-liquid separation applications. Depending on design and shape, these plates can remove droplets larger than 8 microns.
Advantages of blade assembly defogger/V-plate defogger:
Experience:
Droplets shoot out of the gas at multiple gentle angles to minimize destructive vortices in the corners. The metal plate is held in place by a slotted frame with equal spacing. We care about the details of each application.
High quality:
As you walk on the finished blade assembly defogger, you can feel its strength and stiffness. Thicker steel plates resist vibration and have longer service life in corrosive and aggressive environments. Once installed in a container, little maintenance is required.
Lower pressure drop:
A flat board Angle means a lower pressure drop than a board with sharp corners and drainage hooks. Especially in some applications, such as vacuum towers, it can make a big difference.
Higher efficiency:
Reduced turbulence at the corner also means that secondary entrainment of the liquid discharged along the plate is minimized.
Generally, the removal efficiency of droplet with diameter of 20 micron and above is more than 90%. For droplets 40 micron and above, the removal efficiency can reach 99.9%.
Higher throughput:
It allows for higher air velocities than the mesh mat defogger without losing efficiency due to secondary enlistment.
Materials suitable for your craft:
The most common building materials are carbon steel, 304 and 316 stainless steel. But we understand your corrosion requirements and can supply other alloy or non-metal structures according to the order.
Hook plate for special application:
For PP materials, blade plates with small hooks are optional. For stainless steel materials, blades can be welded from one or more angles with a short hook. Some users prefer this style to help prevent liquid re-entrainment.
Vane Pack mist eliminator datasheet:
| data sheet of demister | |||||
| 1. | Project No.: | ||||
| 2. | Equipment name | Vane demister | |||
| 3. | Quantity | In use | quantity | 1 | |
| Spare parts | quantity | 0 | |||
| Total | quantity | 1 | |||
| 4. | Purpose |
Removal of slurry droplets in FGD emission And control the dust emission concentration at the outlet of absorption tower |
|||
| 5. | Basic design conditions | ||||
| 1) Characteristics of flue gas | |||||
| (1) Name of flue gas | Flue gas after dust removal and desulfurization | ||||
| (2) Flue gas flow at absorber inlet | m3/h | 31000 | |||
| (3) Dust concentration at absorber inlet | mg/Nm3 | ≤20(Standard state dry basis,3%O2) | |||
| Flue gas flow at absorber outlet | m3/h | 32500 | |||
| Flue gas velocity | m/s | ≤2.0 | |||
| (4) Outlet temperature of absorption tower | ℃ | 45 | |||
| (5) pressure | kPa･G | 1.0 | |||
| (6) Expected flue gas composition | See Table 1 | ||||
| H2O | (liquid) | wt% | ~95 | ||
| Na2S | (solid) | wt% | 4 | ||
| Na2HS | (solid) | wt% | 1 | ||
| Droplet characteristics | |||||
| Density | kg/m3 | ~1020 | |||
| PH | － | 7~10 | |||
| Viscosity | cPa | <3 | |||
| 2) Type of demister | As per order | ||||
| 3) Installation position | Upper part of absorber | ||||
| 6. | Structural design conditions | ||||
| 1) Standards, specifications | As per order | ||||
| 2) Design pressure of absorber | kPa·G | -1.0~+5.0 | |||
| 9) Design temperature(maximum temperature and time of mist eliminator) | Depends on material | ||||
| Shell | ℃/min | ||||
| demister | ℃/min | ||||
| 3) Corrosion allowance | |||||
| 4) Shell size of demister | Inner diameter of absorption section of absorption tower Φ 2.6m | ||||
| 5) texture of material | |||||
|
|||||
|
304, 316L, 2205, 2507, TA2, etc. | ||||
|
|||||
|
|||||
|
|||||
Package and Shipment
Our Company
Boeeger Industech Limied, build in 2004, has 17 years of export experience, is a ONE-STOP SUPPLIER OF PACKING PRODUCTS. We are located in the hometown of China's wire mesh, close to Beijing airport and Tianjin port, so it is convenient and fast transportation. No matter how large or small your company is, you can find products suitable for you here, and you don’t need to worry about payment, quality inspection, packaging and shipment. We have a professional team to provide you with the best solution to solve all your problems.
For special using, we also handle custom fabricated needs.Our well-trained staff have an extensive knowledge of the filtering industry and are always willing to assist with our customer’s needs.
When quality at the right price counts, make it Boegger!
FAQ
Q1:What's the MOQ?
A1 : The MOQ is 1 set.
Q2 : What are the terms of payment?
A2 : T/T , L/C at sight, Paypal , etc.
Q3 : What's the delivery time?
A3 : About 7-10 days .after received the payment.
Q4 : Do you do customized order?
A4 : Yes, of course.
Q5:Can I negotiate the price?
A5: Yes, we may consider the discounts for mixed goods or bulk orders of individual products.
Q6:What information should I offer to you if I want to know the price?
A6: Material, Size,Application/Usage, Quantities, Payment termFOB or CIF, Package term
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.