120W P67 Waterproof LED Power Supply DC 12V ~ 48V
DC 12V ~ 48V 120W P67 Waterproof LED Power Supply
Feature
- Wide input voltage range 200-240Vac;
- Built-in active PFC function
- High efficiency, low temperature rise, high reliability
- Built-in EMI filter, Lower ripple & noise
- Built-in input undervoltage protection
- Overvoltage/overload/short circuit/over temperature protection
- Output constant voltage and Constant current hybride mode
Specifications:
Electrical / Optical Characteristics (Ta=25℃±3℃)
| Type | LED Power Supply |
| Output Power | 120 W |
| Output Voltage | 24V,12V |
| Output Type | Single port |
| Input Voltage | 110V,220V ac |
| Output Frequency | 50/60Hz |
| Output Current | 10A |
| Driving Type | Constant Voltage |
| IP Grade | IP67 |
| Warranty |
3 years |
Advantage:
- Protections:short circuit/over load/over voltage/over temperature
- IP67 design for indoor or outdoor installation
- It can be used in dry ,wet and rainy environment Cooling by free air, high reliability
- 100% full load burn-in test
- Suitable for internal lights application for Ⅰ/Ⅱ/Ⅲ. Widely used in LED lighting and IT equipment
- IS 15885(Part2/Sec13)
- Compliance to worldwide safety regulation for led lightings.
Applications:
- Used in back light of light box, landscape layout and stage adornment, spray, blister word, etc.
- For Advertisement Signs Backlightings and LED Module Channel Letters
Product details
| Model | W1P2-H350-V012 | ||||
| Input | Rated Input Voltage | 200-240Vac | |||
| Input Voltage Range | 180～264Vac | ||||
| Frequency Range | 47～63(Typ. 50/60)HZ | ||||
| Max. Input Current | ≤3.5A | ||||
| Inrush Current | ≤25A | ||||
| PF | ≥0.95 | ||||
| THD | ≤15% | ||||
| Output | Rated output voltage | 12V | |||
| Rated Output Current | 29A | ||||
| Max. Output Power | 348W | ||||
| Efficiency | ≥90%(Typical 92%) | ||||
| Output Ripple & Noise | ≤300mVp-p | ||||
| Line regulation | ±1% | ||||
| Load regulation | ±2% | ||||
| Voltage tolerance | ≤±2% | ||||
| Environment Condition | Range of working temperature | -40~ +70(Typ. 25)℃ | |||
| Storage temperature | -45~+85(Typ. 25)℃ | ||||
| Relative Humidity | 10～95% | ||||
| Cooling Method | Air Convection | ||||
| Altitude | 0～5000m | ||||
| Protection Rating | IP67 | ||||
| Max. Case Temperature | 90℃ | ||||
| Safety | Leakage Current | ≤0.7mA | 240Vac/60Hz | ||
| Hi-pot | Input To Output | 3750Vac 60S,current≤10mA | No arc, no breakdown |
||
| Input To FG | 1750Vac 60S,current≤10mA | ||||
| Output To FG | 500Vac 60S,current≤10mA | ||||
| Insulation resistance | Input To Output | ≥10MΩ@ 500Vdc | 90%RH, 500VDC | ||
| Input To FG | ≥10MΩ@ 500Vdc | ||||
| Output To FG | ≥10MΩ@ 500Vdc | ||||
| Safety Standard | Compliance to IEC/EN61347-1,EN61347-2-13, GB19510,UL1310,CCC,CB+CE(TUV) Passed |
||||
| EMC | Harmonic Current | Compliance to IEC 61000-3-2 Class C (@Load≥50%) |
|||
| Conducted Emissions (CE) | EN55015 | ||||
| Radiated Emissions (RE) | EN55015 | ||||
| Radiated, Radio-Frequency, Electromagnetic Field Immunity (RS) | IEC 61000-4-3 Level 2, IEC61547, Criterion B | ||||
| Conducted Immunity (CS) | IEC 61000-4-6 Level 2, IEC61547, Criterion B | ||||
| Electrical Fast Transient (EFT)/Burst | IEC 61000-4-4 Level 2, IEC61547, Criterion B | ||||
| Surge | IEC 61000-4-5 Differential Mode: ±2kV Common Mode: ±4kV Criterion B |
||||
| Protection | Over voltge protection | ≤15V | |||
| Over-temperature protection | 70-80℃ | Ambient Temperature, rated load | |||
| Input under voltage recovery value | 160～180Vac | ||||
| Output short-circuit protection | Hiccup mode, auto-recovery after fault condition is removed | ||||
| Reliability | MTBF | 25℃:100000Hrs,MIL-217 Method | |||
| Others | Dimension | 245*90*45(L*W*H) | |||
| Cooling method | √Ventilation Cooling ⬜air cooling | ||||
| Extension method | ⬜Three-proofing lacquer ⬜Stamped ⬜Low temperature start-up(-40℃)⬜Others |
||||
| Note | *Unless otherwise specified, all specifications are measured at an input of 230VAC, rated load, 25°C. *In order to extend the service life, it is recommended to leave an additional 30% margin when configuring the load. For example, if the device requires 100W of power, the power supply of not less than 130W is selected. * Switching power supply ripple test method: test on the power supply output terminal with a 20MHz oscilloscope, the ground length of the oscilloscope probe is not more than 12mm, and the probe input is paralleled with 47uF electrolytic capacitors and 0.1uF high frequency capacitors. *The power supply is part of the equipment system components, and all EMC tests need to be confirmed in conjunction with the end equipment for electromagnetic compatibility. |
||||
FAQ
120W Waterproof LED Power Supply IP67 For LED Modules Strip Light DC12V 10A, For Lighting Box Use For Sign Backlight For Outdoor Advertising Sign Backlight
Q1. Can I have a sample order for this IP67 LED Power Supply 12V 10A?
A: Yes, we welcome sample order to test and check quality. Mixed samples are acceptable.
Q2. What about the lead time?
A: 3-5 days for Sample preparing ,8-10 working days for mass production.
Q3. Do you have any MOQ limit for IP67 LED Power Supply 12V 10A?
A: Low MOQ, 1pc for sample checking is available.
Q4. How do you ship the goods and how long does it take to arrive?
A: Ship by DHL, UPS, FedEx or TNT. It takes 3-5 days to arrive. Airline and sea shipping also optional.
Q5. How to proceed an order for IP67 LED Power Supply 12V 10A?
A: Firstly let us know your requirements or application.
Secondly We quote according to your requirements or our suggestions.
Thirdly customer confirms the samples and places deposit for formal order.
Fourthly We arrange the production.
Q6. Is it OK to print my logo on IP67 LED Power Supply 12V 10A product?
A: Yes. Please inform us formally before our production.
Q7: Do you offer guarantee for the products?
A: Yes, we offer 3 years warranty to our products.
Q8: How to deal with the faulty?
Firstly, Our products are produced in strict quality control system and the defective rate will be less than 0.3%.
Secondly, during the guarantee period, we will send new lights with new order for small quantity. For defective batch products, we will repair them and resend them to you or we can discuss the solution including re-call according to real situation.
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.