150W 200W 350W 24V LED Power Supply For CCTV Camera LED Light
5V 12V 24V 50W 100W 150W 200W 350W Smps Power Supply For CCTV Camera And LED Light
So how do I know what type of LED driver I need?
The case for constant current drivers:
If you take a look at high powered LEDs, one unique characteristic is the exponential relationship between the applied forward voltage to the LED and the current flowing through it. You can see this clearly from the electrical characteristics of the Cree XP-G2 below in Figure 1. When the LED is turned on, even the smallest 5% change in voltage (2.74V to 2.87V) can create a 100% increase in current driven to the XP-G2 as you can see at the red marks current went from 350mA to 700mA.
Specification
| Product Name: | switch power supply | Output Power: | 15w-1000w |
| Quality: | 100%Factory | Output Type: | Single |
| Protections: | Short Circuit Overload Overvolt Overtemp | Input Voltage: | 254-370 VDC |
| Application: | LED, CCTV and so on | Output Voltage: | 5V,12V,24V,36V,48V |
| Certification: | CE RoHS ISO9001 CCC | Output Frequency: | 47-63Hz |
| Size: | 215*115*50mm | Output Current: | 0.31-66.5A |
| Project | Technical index | ||||||
| Output | DC voltage | 5V | 12V | 18V | 24V | 36V | 48V |
| Rated current | 50A | 29A | 19.4A | 14.5A | 9.7A | 7.3A | |
| Rated power | 250W | 350W | 350W | 350W | 350W | 350.4W | |
| Ripple and noise ① | ＜150mV | ＜150mV | ＜150mV | ＜150mV | ＜240mV | ＜240mV | |
| Voltage accuracy | ±2% | ±1% | |||||
| Output voltage regulation range | ±10% | ||||||
| Load adjustment rate | ＜±1.5% | ＜±1.2% | ＜±1.2% | ＜±1% | ＜±0.5% | ＜±0.5% | |
| Linear adjustment rate | ＜±1% | ||||||
| Input | Voltage range | 90-132VAC/180-264VAC 47Hz～63Hz；254VDC～370VDC | |||||
| Efficiency (typical) ② | ＞74% | ＞82% | ＞82% | ＞84% | ＞86% | ＞86% | |
| Working current | ＜5.2 A 115VAC ＜2.8A 230VAC | ||||||
| Impulse current | 110VAC 25A, 220VAC: 50A | ||||||
| Start, rise, hold time | 200ms,50ms,20ms :230VAC | ||||||
| Protect | overload protection | 105% - 135% type: constant current output + VO reduced to undervoltage point cut off output reset: power on again | |||||
| Overvoltage protection | Close output when ≥ 115% - 145% | ||||||
| Undervoltage protection | Close output when ≤ 10% - 45% | ||||||
| Short circuit protection | Close output | ||||||
| Over temperature protection | Rth3: ≥ 65 ℃ fan start, ≥ 55 ℃ fan close, ≥ 80 ℃ close output (5v-15v) rth3: ≥ 70 ℃ fan start, ≥ 60 ℃ fan close, ≥ 85 ℃ close | ||||||
| output (18v-48v) | |||||||
| Environmental Science | Working temperature and humidity | -10℃～+50℃；20%～90RH | |||||
| Storage temperature and humidity | -20℃～+85℃；10%～95RH | ||||||
| Safety regulations | Withstand voltage | Input output: 1.5kVac input shell: 1.5kVac output shell: 0.5kvac for 1 minute | |||||
| Leakage current | Input output < 6mA at 1.5kVac | ||||||
| Leakage current | < 1.5mA at input-output 220VAC | ||||||
| Isolation resistance | Input output, input shell, output shell: 500VDC / 100M Ω | ||||||
| Other | size | 215*115*50mm | |||||
| Net weight / gross weight | 874.1/936.3g | ||||||
| Remarks | ① Ripple and noise measurement method: use a 12 "twisted pair, and connect 0.1uF and 47uF capacitors in parallel at the terminal, | ||||||
| and measure at 20MHz bandwidth. ② The efficiency is tested at an input voltage of 230VAC, rated load, and an ambient temperature | |||||||
| of 25 ℃. Accuracy: including setting error, linear adjustment rate and load adjustment rate. Linear regulation test method: under | |||||||
| rated load from low voltage to high voltage test load regulation test method: from 0% - 100% rated load. The start-up time is | |||||||
| measured under the cold start state. The quick and frequent switch on and off may increase the start-up time. When the operating | |||||||
| altitude is higher than 2000m, the operating environment temperature needs to be reduced by 5 ℃ / 1000m | |||||||
FAQ
Q1:How many Voltage you can supply?
A: 12v , 24v , 48v ,50v , 60v , 110v(Depend on items).
Q2:Can I have a sample order?
A: Yes, we welcome sample order to test and check quality.Mixed samples are acceptable.
Q3:Do you have any MOQ limited for the order?
A: Low MOQ, 1pc for sample checking is available.
Q4:How do you ship the goods and how long does it take to arrive?
A: We usually ship by DHL, UPS, FedEx or EMS. It usually takes 3-5 days to
arrive. Airline and sea shipping also optional.
Q5:Do you offer guarantee for the products?
A: Yes, we offer warranty to our products.
Q6: How to deal with the faulty?
A: Firstly, our products are produced in strict quality control system and the defective rate will be less. Secondly, during the guarantee period,we will send new product with new order for small quantity. For defective batch products, we will repair them and resend them to you or we can discuss the solution including re-call according to real situation.
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.