Antirust 0.25mm Wire Mesh Demister For Low Pressure Rectifying Column
Low Pressure Rectifying Column 0.25mm Wire Mesh Demister
Wire Mesh Demister Information
Wire mesh demister is used to separate mixture of vapor liquid in some industrial applications. Sometimes a vapor-liquid separator may also referred to as a flash drum, knock-out drum, compressor suction drum or compressor inlet drum. It is usually called mist eliminator when used to remove suspended water droplet from air stream.
Normally, in the vertical vessels, the liquid drops to the bottom, where they are withdrawn, as the force of gravity. But in low gravity environments like a space station, the gravity is not usable effectively. At this time, centrifugal force needs to be utilised in a spinning centrifugal separator to drive liquid droplets to the outer edge of the device while gas migrates to the centre.
In either way of separation, the gas outlet can be surrounded by a spinning mesh screen or grating. If any droplets occasionally reach the outlet, they will strike the grating, be accelerated and thrown away from the outlet.
The vapor goes through the mist eliminator at a designed velocity which minimizes the re-entrainment of any liquid droplets.
The feed to a vapor-liquid separator may also be a kind of liquid which is being partially or totally flashed into a vapor when it enters the device.
Only when there is air space inside the chamber, the vapor-liquid separator is effective. It can fail either when the mixed stream inlet is overwhelmed or the draining of collected liquid is slower than its growing. Considering this, the separator may be combined with some liquid level sensing accessories, such as a sight glass or float sensor. By doing this, both the supply and drain flow can be regulated to prevent the separator from being overloaded.
Selected wire mesh form of demister
| Specifications of standard type demister pad | ||||||
| Item | Wire type | Wire size (mm) |
Wire width tolerance (mm) |
Bulk density (kg/m3) |
Specific surface area (m2/m3) |
porosity |
| SSTDPAHS-01 | Flat wire | 0.1 × 0.4 | +10/-0 | 150 | 475 | 0.981 |
| SSTDPAHS-02 | Round wire | 0.23 | 320 | |||
| Note: every 100 mm thick mat has 25 layers of wire mesh. | ||||||
| Specifications of efficient type demister pad | ||||||
| Item | Wire type | Wire size (mm) |
Wire width tolerance (mm) |
Bulk density (kg/m3) |
Specific surface area (m2/m3) |
porosity |
| ETDP-01 | Flat wire | 0.1 × 0.3 | +10/-0 | 182 | 626 | 0.977 |
| ETDP-02 | Round wire | 0.19 | 484 | |||
| Note: every 100 mm thick mat has 32 layers of wire mesh. | ||||||
| Specifications of high-penetration type demister pad | ||||||
| Item | Wire type | Wire size (mm) |
Wire width tolerance (mm) |
Bulk density (kg/m3) |
Specific surface area (m2/m3) |
porosity |
| HP-01 | Flat wire | 0.1 × 0.4 | +10/-0 | 98 | 313 | 0.9875 |
| HP-02 | Round wire | 0.23 | 4217 | |||
| Note: every 100 mm thick mat has 20 layers of wire mesh. | ||||||
| Specifications of shock absorber type demister pad | ||
| Item | Specification | Filament specifications (mm) |
| AHS-01 | 33-30 type | 0.08 |
| AHS-02 | 38-40 type | 0.08 |
| AHS-03 | 20-40 type | 0.22 |
| AHS-04 | 30-40 type | 0.1/0.12 |
| AHS-05 | 30-50 type | 0.16 |
| AHS-06 | 40-60 type | 0.12 |
| AHS-07 | 30-80 type | 0.22 |
| AHS-08 | 50-120 type | 0.22 |
| AHS-09 | 40-120 type | 0.22 |
| Type | Standard wire specification |
| SP | 0.1 mm + 0.03 mm × 0.4 mm |
| DP | 0.1 mm + 0.02 mm × 0.3 mm |
| HR | 0.23 mm + 0.03 mm × 0.4 mm. |
| HP | 0.1 mm + 0.03 mm × 0.4 mm |
Working Principle Of Wire Mesh Demister
When mist in the gas rises at a constant speed, then the mist eliminator works where vapor strikes the mesh surface filament and liquid start coalescing. After some time, liquid droplet size goes up and it gets isolated from the filament.
Wire Mesh Demister Characteristic
-
Structure simple, weight light.
-
The high factor of porosity, and low head loss.
-
Great contact surface area, high removing foam ratio.
-
The convenience of installing, operating, and repairing.
Wire Mesh Demister Application
Wire mesh demister pads are used in chemical, petroleum, sulfate, medicine, light industry, metallurgy, machine, building, construction, aviation, shipping, and environment protection.
Company Profile
Anping County Hardware Mesh Products Co., Ltd. is located in Anping County, Hebei Province, known as the "Hometown of Chinese Wire Mesh". The company is a dedicated manufacturer of wire mesh demisters. The company has more than 90 sets of knitted mesh equipment. The wire mesh demister is the main product of our company. Most of our employees are operation, maintenance, and installation personnel with practical experience, who can provide customers with the required engineering consultation and installation of tank filtration. solution.Nearly 20 years of experience in the production of mist eliminator mats, knitted wire mesh, and other packaging materials.
We have ISO9001 certification and a strict quality control system in the QC department of the enterprise.
We claim that all mist eliminator pads our customers receive are qualified and perform perfectly. We have different specifications.
The filtration fineness can reach 3μm~5μm. In addition to standard and popular sizes, we can also customize specific applications according to customer needs.
During the company's development, through continuous on-the-spot inspections, personal exchanges and cooperation with customers, and comprehensive discounts and technical support, we have won strong customer support and praise.
The company's performance has maintained an annual output value growth rate of 30-40. Our employees pursue the policy of "enterprising, truth-seeking, rigorous and united", continue to develop and innovate, take technology as the core, and wholeheartedly provide you with cost-effective products, high-quality engineering design, and services.
Welcome customer consultation and I sincerely look forward to cooperating with you!
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.