GE Fanuc 16-Channel Analog Voltage Input Module IC693ALG223 for Remote I/O Devices
IC693ALG223 GE Fanuc 16-Channel Analog Voltage Input Module
Product Description of IC693ALG223
IC693ALG223 is a PACSystems Series 90-30 RX3i Analog Current Input Module that offers 16 channels. The module’s 16 separate and single ended channels can be configured for any of the following three ranges: 4 to 20 mA, 0 to 20 mA, or 4 to 20 mA Enhanced. Both high and low alarms are obtainable on each range. In the enhanced range, the IC693ALG223 module can be set with a low alarm limit to detect input current with open wire fault detection in the 4 to 20 mA applications; high alarm alerts can also be set by the user. Additionally, this module reports status, including power supply standing to the CPU. IC693ALG223 can be used in any I/O slot that offers a serial connector in the RX3i or Series 90-30 system.
Specific to the IC693ALG223 module, 120 mA from a 5 VCD bus on the controller backplane is consumed. This also needs a 65 mA plus current loop from a +24 VDC supply supplied by the user. An update rate of 6 ms is standard with isolation of 250 VAC continuous or 1500 VAC for one minute. When scanning active channels, the number of channels to be scanned will be completed in serial order. Analog values are scaled over the entire range of the converter with factory calibration adjusting the analog value per bit. RX3i racks support upgrades to the firmware associated with this module, but this does not include 90-30 racks. The IC693ALG223 is also equipped with LED status lights emitting ON, OFF, and FAIL to assist the user in operation and troubleshooting.
Technical Specifications of IC693ALG223
| No. of channels: | 1 to 16 selectable |
| Input Current Range: | 0 to 20 mA, 4 to 20 mA and 4 to 20 mA enhanced |
| Calibration:: | Factory calibrated to 4 µA per count or 5 µA per count |
| Update Rate: | 13 msec (all 16 channels) |
| Input Filter Response: | 19 Hz |
| Power Consumption: | 120 mA from the +5 V bus or 65 mA from the +24 V bus |
The GE Fanuc IC693ALG223 16-Channel Analog Input Module comes with an input filter response frequency of 200 Hertz and an input impedance of 250 Ohms. The total number of analog current inputs that can be installed in the system is 4 along with the 323, 313, and 311 CPUs, and 8 analog current inputs can be installed with the 331 CPU, and 12 inputs can be installed with the 341and 340 CPUs. This unit comes with a high level of resolution and accuracy that helps it to deal with analog signals that are highly sensitive. The module also receives analog inputs from a wide range of sensors like the level sensors, temperature sensors, and flow sensors. For the IC693ALG223 Analog Input Module to achieve the needed accuracy level, the input channels come with resolution of 4 microamps at 4 to 20 milliamps of current, and a resolution of 5 microamps at 0 to 20 milliamps.
Features of IC693ALG223
- Resolution:
- @ 4 to 20mA: 4µA (4µA/bit)
- @ 0 to 20mA: 5µA (5µA/bit)
- @ 4 to 20mA Enhanced: 5µA (5µA/bit)
- Absolute accuracy:
- ±0.25% of full scale @ 25°C (77°F)
- ±0.5% of full scale over specified operating temperature range
- Linearity:
- <1 LSB from 4 to 20mA (4 to 20mA range)
- <1 LSB from 100µA to 20mA (0 to 20mA and 4 to 20mA Enhanced ranges)
- 1,500V isolation between field side and logic side
- 0V common mode voltage (single-ended channels)
- >80db cross-channel rejection from DC to 1 kHz
- 250 ohms input impedance
- 19Hz input low pass filter response
- 20 to 30VDC external supply voltage range
- 10% external supply voltage ripple
- Internal power consumption:
- 120mA from the +5V bus on the backplane
- 65mA from 24VDC external user supply (in addition to current loop currents)
Similar Products
| SGDM-01AD |
| SGDM-01ADA |
| SGDM-01ADA/SGDH-01AE+SGMAH-01AAA21 |
| SGDM-01ADA+SGMAH-01AAAG761 |
| SGDM-01ADA-RY5 |
| SGDM-01BDA |
| SGDM-02ADA |
| SGDM-02ADA/SGDH-02AE+SGMAH-02AAA21 |
| SGDM-02ADA+SGMAH-02AAA2C |
| SGDM-02ADA+SGMPH-02AAA41 |
| SGDM-02ADA+SGMPH-02A1A21 |
| SGDM-02AD-R |
| SGDM-02BDA |
| SGDM-02BDA |
| SGDM-02BDA+SGMAH-02BBAB1 |
| SGDM-04AC-AD2B |
| SGDM-04AC-SD1 |
| SGDM-04AC-SD2A |
| SGDM-04ACSD2B |
| SGDM-04AC-SD2B |
| SGDM-04AC-SD2BM |
| SGDM-04AC-SD2M |
| SGDM-04AD |
| SGDM-04AD+SGMAH-04AAA41 |
| SGDM-04ADA |
| SGDM-04ADA +SGMAH-04AAA21 |
| SGDM-04ADA +SGMAH-04AAA41 |
| SGDM-04ADA+SGMPH-04A1A21 |
| SGDM-04ADA-RY1 |
| SGDM-04ADAY360 |
| SGDM-04AD-R |
| SGDM-04AD-RY1 |
| SGDM-04ADY39 |
| SGDM-05ADA |
| SGDM-05ADA+SGMAH-A5AAA21 |
| SGDM-05ADA+SGMGH-05ACA6 |
| SGDM-05ADAY118 |
| SGDM-05ADAY61 |
| SGDM-08AC-SD1 |
| SGDM-08AC-SD2A |
| SGDM-08AC-SD2B |
| SGDM-08AC-SD2BM |
| SGDM-08AC-SD2M |
| SGDM-08ADA |
Similer item we can supply:
| HC-UFS13 | HC-UFS23 | HC-UFS73 | HC-UFS43 |
| HC-UFS72 | HC-UFS152 | HC-UFS202 | HC-UFS352 |
| HC-UFS502 | HC-SFS81 | HF-KP13 | HF-SP102B |
| HC-SFS121 | HC-RFS153 | HF-MP13B | HF-SP152B |
| HC-SFS201 | HC-RFS203 | HF-MP23B | HF-SP202B |
| HC-SFS301 | HC-RFS353 | HF-MP43B | HF-SP352B |
| HC-SFS52 | HC-RFS503 | HF-MP73B | HF-SP502B |
| HC-SFS102 | HA-LFS11K2 | HF-KP13B | HF-SP51 |
| HC-SFS152 | HA-LFS15K2 | HF-KP23B | HF-SP702B |
| HC-SFS202 | HA-LFS22K2 | HF-KP43B | HF-SP81 |
| HC-SFS352 | HA-LFS11K2B | HF-KP73B | HF-SP121 |
| HC-SFS502 | HA-LFS15K2B | HF-SP52 | HF-SP201 |
| HC-SFS702 | HA-LFS22K2B | HF-SP102 | HF-SP51B |
| HC-SFS53 | HF-MP053 | HF-SP152 | HF-SP81B |
| HC-SFS103 | HF-MP13 | HF-SP202 | HF-SP121B |
| HC-SFS153 | HF-MP23 | HF-SP352 | HF-SP201B |
| HC-SFS203 | HF-MP43 | HF-SP502 | HC-SFS202K |
| HC-SFS353 | HF-MP73 | HF-SP702 | HC-SFS201B |
| HC-RFS103 | HF-KP053 | HF-SP52B | HC-SFS202B |
Advantage Products:
【Yaskawa】Servo Drive / Servo Motor
【Mitsubishi】Servo Drive / Servo Motor
【Honeywell】Module DCS / PLC
【Emerson】DeltaV Module / Servo Motor
【ABB】Input Output Module
【AB】Module / Touch Screen
【Rosemount】Pressure and Temperature Transmitter
【Yokogawa】Pressure Transmitter
【GE】IC69 Series PLC/ Fanuc Servo Motor and Drive
Wisdomlong Technology CO.,LTD
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.