SCBE-141N Axial Lead Glass Discharge Tube SPG 140 VS Spark Gap Arrester
SOCAY SCBE Series Glass Discharge Tube SCBE-141N SPG 140VS Low Electrode Capacitance (≤1.0pF)
DATASHEET: SCBE_v2204.1.pdf
| Part Number |
DC Spark-over Voltage Vs(V) |
Minimum Insulation Resistance IR(OHM)/DC |
Maximum Capacitance 1KHZ-6Vmax C (pF) |
Surge Current Capacity 8/20 μS |
Surge Life Test |
| SCBE-141N | 140(98~182) | 100M / 50V | 1.0 | 1000A | 10KV / 150A , >200T |
| SCBE-201M | 200(160~240) | 100M /100V | 1.0 | 1000A | 10KV / 150A , >200T |
| SCBE-251M | 250(200~300) | 100M /100V | 1.0 | 1000A | 10KV / 150A , >200T |
| SCBE-301M | 300(240~360) | 100M /100V | 1.0 | 1000A | 10KV / 150A , >200T |
| SCBE-401M | 400(320~480) | 100M / 250V | 1.0 | 1000A | 10KV / 150A , >200T |
| SCBE-501M | 500(400~600) | 100M / 250V | 1.0 | 1000A | 10KV / 150A , >200T |
| SCBE-601M | 600(480~720) | 100M / 250V | 1.0 | 1000A | 10KV / 150A , >200T |
| SCBE-102M | 1000(800~1200) | 100M / 500V | 1.0 | 1000A | 10KV / 150A , >200T |
| SCBE-122M | 1200(960~1440) | 100M / 500V | 1.0 | 1000A | 10KV / 150A , >200T |
Features:
|
u Approximately zero leaking current before clamping voltage u Less decay at on/off state. u High capability to withstand repeated lightning strikes. u Low electrode capacitance (≤1.0pF) and high isolation (≥100MΩ). u RoHS compliant. u Bilateral symmetrical. u Temperature, humidity and lightness insensitive. u Working temperature: -45℃~ +125 ℃ u Storage temperature: -45℃~ +125 ℃ u Meets MSL level 1, per J-STD-020 |
Applications:
|
u Power Supplies u Motor sparks eliminating u Relay switching spark absorbing u Data line pulse guarding u Electronic devices requiring UL497A and UL497B compliant u Telephone/Fax/Modem u High frequency signal transmitters/receivers u Satellite antenna u Radio amplifiers u Alarm systems u Cathode ray tubes in Monitors/TVs |
| Part Number | Color Code1 | Color Code2 | Color Code3 |
| SCBE-141N | Brown | Red | White |
| SCBE-201M | Red | Orange | Blue |
| SCBE-251M | Red | Orange | Green |
| SCBE-301M | Orange | Red | White |
| SCBE-401M | Yellow | Black | Brown |
| SCBE-501M | Green | Yellow | Orange |
| SCBE-601M | Blue | Red | Yellow |
| SCBE-102M | Black | Orange | Red |
| SCBE-122M | Black | Red | Orange |
Hand Soldering
Solder iron temperature: 350±5℃
Heating time: 3 seconds max.
General attention to soldering
- High soldering temperatures and long soldering times can cause leaching of the termination, decrease in adherence strength, and the change of characteristic may occur.
- For soldering, please refer to the soldering curves above. However, please keep exposures to temperatures exceeding 200℃ to fewer than 50 seconds.
- Please use a mild flux (containing less than 0.2wt% CI). Also, if the flux is water soluble, be sure to wash thoroughly to remove any residue from the underside of components that could affect resistance.
Cleaning
When using ultrasonic cleaning, the board may resonate if the output power is too high. Since this vibration can cause cracking or a decrease in the adherence of the termination, we recommend that you use the conditions below:
Frequency: 40kHz max.
Output power: 20W/liter
Cleaning time: 5 minutes max.
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.