Low Capacitance Thyristor Surge Suppressors TSS Semiconductor Component P0640SB
Low Capacitance Thyristor Surge Suppressors TSS Semiconductor Component P0640SB
DATASHEET: PXXX0SB_v2103.1.pdf
| Part Number | Marking | VDRM @IDRM=5μA |
VS ① @100V/μS |
VT @IT=2.2A | IS | IT | IH |
C0 ② @1MHz, 2V bias |
| V min | V max | V max | mA max | A max | mA min | pF typ | ||
| P0080SB | P008B | 6 | 25 | 4 | 800 | 2.2 | 50 | 80 |
| P0300SB | P03B | 25 | 40 | 4 | 800 | 2.2 | 50 | 80 |
| P0640SB | P06B | 58 | 77 | 4 | 800 | 2.2 | 150 | 80 |
| P0720SB | P07B | 65 | 88 | 4 | 800 | 2.2 | 150 | 75 |
| P0900SB | P09B | 75 | 98 | 4 | 800 | 2.2 | 150 | 70 |
| P1100SB | P11B | 90 | 130 | 4 | 800 | 2.2 | 150 | 70 |
| P1300SB | P13B | 120 | 160 | 4 | 800 | 2.2 | 150 | 65 |
| P1500SB | P15B | 140 | 180 | 4 | 800 | 2.2 | 150 | 65 |
| P1800SB | P18B | 170 | 220 | 4 | 800 | 2.2 | 150 | 65 |
| P2300SB | P23B | 190 | 260 | 4 | 800 | 2.2 | 150 | 60 |
| P2600SB | P26B | 220 | 300 | 4 | 800 | 2.2 | 150 | 60 |
| P3100SB | P31B | 275 | 350 | 4 | 800 | 2.2 | 150 | 50 |
| P3500SB | P35B | 320 | 400 | 4 | 800 | 2.2 | 150 | 50 |
| P4200SB | P42B | 400 | 520 | 4 | 800 | 2.2 | 150 | 40 |
|
Notes: ① Vs is measured at 100KV/s. ② Off-state capacitance is measured in VDC=2V, VRMS=1V, f=1MHz. |
||||||||
Introduction:
The TSS are characterised by precise conduction, fast response, high surge absorption capacity, biaxial symmetry and high reliability.
Working Principle
When connected in parallel to a circuit and the device is not moving, the resistance value is high and can be considered as an open circuit with little or no effect on the circuit. When there is an abnormal pulse, the resistance value drops instantly, releasing the current momentarily. When the abnormal high voltage disappears, it returns to its high resistance state and the circuit works normally.
| Parameter | Definition |
| IS | Switching Current - maximum current required to switch to on state |
| IDRM | Leakage Current - maximum peak off-state current measured at VDRM |
| IH | Holding Current - minimum current required to maintain on state |
| IT | On-state Current - maximum rated continuous on-state current |
| VS | Switching Voltage - maximum voltage prior to switching to on stat |
| VDRM | Peak Off-state Voltage - maximum voltage that can be applied while maintaining off state |
| VT | On-state Voltage - maximum voltage measured at rated on-state current |
| C0 | Off-state Capacitance - typical capacitance measured in off state |
| Series | 2/10μS1 | 8/20μS1 | 10/160μS1 | 10/560μS1 | 10/1000μS1 | 5/310μS1 |
ITSM 50/60 Hz |
di/dt | |
| 2/10μS2 | 1.2/50μS2 | 10/160μS2 | 10/560μS2 | 10/1000μS2 | 10/700μS2 | ||||
| A min | A min | A min | A min | A min | A min | A min | Amps/µs max | ||
| B | 250 | 250 | 150 | 100 | 80 | 100 | 30 | 500 | |
|
Notes:
|
- Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP ratings applicable over temperature range of -40ºC to +85ºC - The device must initially be in thermal equilibrium with -40°C < TJ < +150°C
|
||||||||
| High Temp Voltage Blocking | 80% Rated VDRM (VAC Peak ) +125°C or +150°C, Lead Material Copper Alloy High Temp Voltage Blocking 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 | |
| Temp Cycling | -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 | |
| Biased Temp & Humidity | 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 | |
| High Temp Storage | +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 | |
| Low Temp Storage | -65°C, 1008 hrs. | |
| Thermal Shock | 0°C to +100°C, 5 min. dwell, 10 sec. transfer, Thermal Shock 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 | |
| Autoclave (Pressure Cooker Test) | +121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/Cooker Test) JEDEC, JESD22-A-102 | |
| Resistance to Solder Heat | +260°C, 30 secs. MIL-STD-750 (Method 2031 | |
| Moisture Sensitivity Level | 85%RH, +85°C, 168 hrs., 3 reflow cycles Level (+260°C Peak). JEDEC-J-STD-020, Level 1 |
| Lead Material | Copper Alloy | |
| Terminal Finish | 100% Matte-Tin Plated | |
| Body Material | UL recognized epoxy meeting flammability classification 94V-0 |
| Part Number | Component Package | Quantity | Packaging Option | Packaging Specification | |
| Pxxx0SB | DO-214AA | 2500 | Tape & Reel -12mm/13″tape | EIA -481 - D |
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.