Wireless magnetic contact JS-55W in 315 or 433MHZ for roller shutter door
www.jsusc.com
JS-55W wireless magnetic door contact,it has the functions of instantly detecting door or window open and close,
tamper protection for shell and battery level real-time checking.
JS-55W can be also connected with our other sensors for your roller door or metal door.
Detector needs to enroll its only address code to wireless host. Besides, it is a separate trigger detector,
which means that it will send alarm signal to alarm host immediately to prevent the intrusion
from door or window and automatic status report enhance its protection.
2.0 Specification
Output: NC type.
Zinc case, grey color
Operation gap ≥50mm
For roller door or metal door
Emission Current: 13mA
Quiescent current ≤10ua
Emission Frequency: 315/433MHz (868/915 available on requested)
Wireless Transmitting Range: 120M open area
Working Environment temperature:-10℃~ +50℃
Wireless chip: EV1527(2262,1920 available on requested)
Alarm Output: alarm, low battery
Automatic status report
battery:Lithium battery CR-2450,
3V, 600mAH
Encoded mode:fixed code
Inner packing: 1pcs/box
Carton:100 pcs/carton
Carton size: 38*30*30CM
G.W.:24.00KGS
N.W.:23.50KGS
JS-55W wireless magnetic door contact,it has the functions of instantly detecting door or window open and close,
tamper protection for shell and battery level real-time checking.
JS-55W can be also connected with our other sensors for your roller door or metal door.
Detector needs to enroll its only address code to wireless host. Besides, it is a separate trigger detector,
which means that it will send alarm signal to alarm host immediately to prevent the intrusion
from door or window and automatic status report enhance its protection.
Output: NC type.
Zinc case, grey color
Operation gap ≥50mm
For roller door or metal door
Emission Current: 13mA
Quiescent current ≤10ua
Emission Frequency: 315/433MHz (868/915 available on requested)
Wireless Transmitting Range: 120M open area
Working Environment temperature:-10℃~ +50℃
Wireless chip: EV1527(2262,1920 available on requested)
Alarm Output: alarm, low battery
Automatic status report
battery:Lithium battery CR-2450,
3V, 600mAH
Encoded mode:fixed code
Inner packing: 1pcs/box
Carton:100 pcs/carton
Carton size: 38*30*30CM
G.W.:24.00KGS
N.W.:23.50KGS
3.0 Installation
After installed batteries, surface mount switch at top or side (NOT on hinge side) of door or hinged window frame.
On double hung window, surface mount the switch at top, side or bottom of window frame.
Surface mount the magnet parallel to the switch, the spacing of these two components as close as possible.
Distance:3mm≤d≤30mm. (Magnetic components is best to use screws. Screw holes in the rear panel, the required hard sharp object poke open) After installing the best antenna all the way out, and then open the windows and doors are monitored,
the Magnetic Red "work instructions" light, while the host and the handset will sound an alarm and instructions,
such as the red light does not shine on the door sensor or host and the handset does not alarm check green "low voltage directive" lamp is lit,
such as light, replace the battery,or contact your supplier. NOT intended for Steel doors or steel windows.
On double hung window, surface mount the switch at top, side or bottom of window frame.
Surface mount the magnet parallel to the switch, the spacing of these two components as close as possible.
Distance:3mm≤d≤30mm. (Magnetic components is best to use screws. Screw holes in the rear panel, the required hard sharp object poke open)
the Magnetic Red "work instructions" light, while the host and the handset will sound an alarm and instructions,
such as the red light does not shine on the door sensor or host and the handset does not alarm check green "low voltage directive" lamp is lit,
such as light, replace the battery,or contact your supplier. NOT intended for Steel doors or steel windows.
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.