Feature	Specification	VPod	VPod II
Displacement	0~1999um, p-p (10~1KHz BP)(0.00~78.7mil)	☑	☑
Velocity	0.0~199.9 mm/s, 0-p (10~1KHz, ISO2954)(0.00~7.87in/sec)	☑	☑
Acceleration	0~19.99 g, rms (10 Hz HP)	☑	☑
Bearing Condition	0.0~199.9 mm/s, (0-p)(500Hz~2KHz)(0.00~7.87in/sec)	☑	☑
Accuracy	5% (10~10KHz)	☑	☑
Battery Indicator	Low/25%/50%/75%/full, graphical indicator	☑	☑
Sensor bias indicator	Normal/open/short, graphical indicator	☑	☑
Back light	LED back light, auto off	☑	☑
Sensor's sensitivity	(100mV/g 30% adjustable)	☑	☑
Housing rating	IP 65, with EMI protection	☑	☑
AC output	2.8V	☑	☑
Power supply	9V alkaline battery *1 (about 30 hours operation)	☑	☑
Auto power off	5 minutes after pressing any key	☑	☑
Display	120*32 graphic mode LCD	☑	☑
Size	180*92*32mm(7.1*3.6*1.2 in)	☑	☑
Weight	About 300gram (including battery)	☑	☑
Hold function	Freeze the display instantly	☑	☑
Average function	Display the average value of the latest 10 data	☑	☑
Peak hold function	Display the maximum value	☑	☑
Gain	*10, and increase the reading precision (by 1 decimal place)	☑	☑
Displacement w/gain	0~199.9um, p-p(0.00~78.7mil)	☑	☑
Velocity w/gain	0.00~19.99mm/s, 0-p(0.000~0.787 in/s)	☑	☑
Acceleration w/gain	0.000~1.999 g,rms	☑	☑
Memory	Memory for 1000 measured data		☑
Riview function	Recall and display the saved data		☑
RS-232C interface	Download a pre-defined route from a PC, or upload archived data to a PC		☑

 

4. Main Features:
4.1 Equipment Description

The vPod and vPod II are microprocessor-based vibration meters. Powered by the microprocessor, this family of meters can easily measure average, hold orpeak hold vibration data, and display them with user selectable unit/detection. The batterycharge indicator and sensor bias indicator is also a standard feature of vPod and vPod II.vPod II has built-in memory for storing up to 1000 archive data points. It can transfer datathrough the RS-232C port with a PC.
4.2 Gain and Precision Reading

For those precision machines that have very lowvibration levels, a precision reading is necessary.In addition to an extra quiet accelerometer that issupplied as a standard accessory, both vPod andvPod II incorporate a built-in gain circuit to amplifysmall vibration signals and show the reading inprecision mode when you turn the gain mode on.This one button gain function allows the user toincrease precision by one decimal place.
4.3 Bearing Condition Measurement
Each vPod and vPod II can measure vibration levels in acceleration, velocity or displacement.The users can select to display the vibration results in their preferable units and detections asshown in the photo above. The vPod and vPod II comes standard with a built-in 500 Hz highpass filter. This is significant because most roller element bearings' parts are locatedbetween 500 Hz - 2 kHz. This high pass filter method has been proven to be very useful inidentifying a bearings condition.
4.4 Memory for Data Storage (vPod II)
With the incorporation of built-in EEPROM memory, a vPod II meter can store up to 1000 setsof vibration data. These saved data points can be recalled by entering the meter's REVIEWmode. Every vPod II comes with an RS-232C interface program for downloading the saveddata from memory to a PC for post analysis or report building.
4.5 Optional PDM Software: TRENDEX
Trendex software coupled with the v-Pod II is a cost effective solution to yourmanagement of machine health condition. Until now, most solutions required veryexpensive analyzers and software analysis programs that collected more data thanwas necessary for most basic predictive maintenance projects.
Trendex is setting the new standard in route collection asset management. Withsimple to use one-click reports, downloading pre-defined routes, trending and alarm analysis, Trendex provides a very cost effective strategy to your data collection needs.
Scheduled Measurement- With Trendex, you can easily download predefined routes.Trending and Alarm Analysis:- With Trendex, easily review and display trending plots showing the history of vibration and alarm conditions as well as a percentage ofchange.
Automatic Reports- With trendex, you can build a custom report for simple one click reports.
4.6 Thermo Meter:
The Trendex software supports both vibration and temperature data. In the route datacollection mode, vPod II also can connect to an optional thermo meter for collectingtemperature data.

 

Suzhou Zero Dynamic Co., Ltd is a top Chinese manufacturer engaging in full automatic balancing equipment and related vibration measurement since 2003.
 
Over the past 20 years, Zero Dynamic has developed 100+ kinds of equipments. We mainly deals with all kinds of advanced dynamic balancing equipment, field dynamic balancing instrument, vibrometer and motor performance testing machine. High revolving speed and high precision are the key features of our products. We have served 3000+ clients in China and abroad, including many world-famous companies such as LG, Black&Decker, Nidec, Huawei, Foxconn, Midea, Ecovas, Daikin, Lexy.
 
Now (2024) Zero Dynamic has a factory of 10,000sqm and more than 120 staff including a professional R&D team of 30+ engineers and 20+ debugging and after-sales team. 

 

As an important participant in Chinese dynamic balancing industry, Zero Dynamic continues to increase the development of new products, and is actively developing into the new energy industry as well as aerospace and other high-speed dynamic balancing and intelligent manufacturing fields, aiming to provide customers with reliable and diversified product choices.