20W Telemetry Mesh Network Radio Long Range Wireless Data Transmission Communication

Price Negotiable

Price: US$665.00~US$775.00

MOQ: 1 set

Delivery Time: 7~14 working days

Brand: Hincn

Product Description

20W Mesh Radio Network Long Range Wireless Data Transmission Telemetry Link

Key Specifications

Modulation	QPSK modulation LDPC coding
RF Power	20W(43dBm)
Bandwidths	1MHz/500kHz/250kHz/125kHz
High sensitivity	-114dBm@125kHz
Wireless transmission delay	Minimum 2ms
Number of nodes	Maximum 1024 nodes

Key Features

Wireless link rate up to 735kbps
Supports point-to-point, point-to-multipoint, multipoint-to-point and Mesh network topologies
Maximum mesh network capacity of 1024 nodes
High sensitivity level of -114 dBm at 125kHz data rate
Frequency hopping spread spectrum (FHSS) support
Air-to-ground LOS distance: ≥300km, ground-to-ground LOS range 3-10km
Dual serial ports support (TTL/RS232/RS422 optional)

Wireless Data Transmitter Overview

The HNC2 self-organizing Mesh network data link radio enables centerless long-range communication between large-scale nodes. Each node can communicate independently without interference, supporting large-scale dense node access to wireless transmission, dynamic networking, and flexible reorganization. The system supports full-multiplexing communication where nodes can simultaneously send and receive data from all other nodes without interference.

HNC2 20W Data Link Mesh Radio Models

Model	RF Power	Network Scale	Frequency Bands
HNC2-H400-20W	20W	Max. 1024 nodes, up to 16 hops	430-450MHz
HNC2-H800-20W			820-854MHz
HNC2-H900-20W			900-940MHz
HNC2-F400-20W	20W	Max. 256 nodes, up to 3 hops	430-450MHz
HNC2-F800-20W			820-854MHz
HNC2-F900-20W			900-940MHz

Technical Specifications

Frequency	Varies by model (see above table)
Bandwidths	1MHz/500kHz/250kHz/125kHz selectable
Number of nodes and hops	Maximum 1024 nodes up to 16 hops or 256 nodes up to 3 hops
Frequency hopping speed	1MHz: Over 1800 times/sec 500kHz: Over 900 times/sec 250kHz: Over 450 times/sec 125kHz: Over 225 times/sec
Effective data rate	1MHz: Up to 735kbps 500kHz: Up to 370kbps 250kHz: Up to 185kbps 125kHz: Up to 92kbps
Full-multiplexing communication	Supported
Air-to-ground LOS distance	≥300km
Centerless self-organized network	Supported - network remains functional if any node is destroyed
Network construction time	Within 1 second
Wireless transmission delay	Minimum 2ms
Dynamic topology	Supports node joining/leaving and topology changes without disruption
RF power	20W(43dBm)
Sensitivity	125kHz: -114dBm 250kHz: -111dBm 500kHz: -108dBm 1MHz: -105dBm
Frequency stability	≤1ppm
Modulation	QPSK modulation LDPC coding
Encryption	128-bit encryption
Low power consumption	Less than 1.5W(0.06A/24V) when receiving Transmission power varies by data rate from 2.4W to 32W
Operating voltage	24V default, supports 7-36V wide voltage input
Operating temperature	-40 to +55°C
Dimensions	83.8 × 53 × 16mm
Weight	91.3g

Input/Output

I/O	Description
Power-in	Power-input, XT30PW-M connector
Dip-switch	Dial switch for configuration mode/transparent transmission mode
Uart 1	Configure/transparent data serial port 1 (TTL 3.3V default, optional RS232/RS422)
Uart 2	Transparent data serial port 2 (TTL 3.3V default, optional RS232/RS422)
ANT	SMA female antenna port (50Ω impedance required)
PWR-LED	Red power status indicator (continuous light when power is normal)
RX-LED	Green data receiving indicator (lights when receiving data)
TX-LED	Green data transmitting indicator (lights when transmitting data)
CA-LED	Blue interference indicator (brightness indicates interference strength)

Operating Modes

The radio supports two operating modes controlled by the dip switch:

Configuration Mode: Uart1 only responds to configuration commands (fixed at 9600 baud, 8 data bits, 1 stop bit, no parity). Only local parameter modifications are possible.
Transparent Transmission Mode: Uart1 handles both configuration packets and transparent data transmission. Supports both local and remote parameter configuration.