PCBA/BGA/LED X-ray Inspection Equipment with Simple Operation
Advanced X-ray inspection system designed for PCBA, BGA, and LED component analysis with intuitive operation and automated capabilities.
- 13*13 cm high-definition large-area digital flat panel detector
- 420*420mm table with 15KG load capacity
- Easy operation - only 2 hours training required
- Hamamatsu tubes ensure extended lifespan and maintenance-free operation
- Programmable inspection procedures for automated high-volume inspection
- Automatic navigation window - table moves to your click location
| X-ray Source | |
|---|---|
| Type | Closed, microfocus |
| Max Tube Voltage | 90kV |
| Max Tube Current | 200μA |
| Focal Spot Size | 5μm |
| Function | Auto preheat |
| Flat Panel Detector | |
|---|---|
| Effective Area | 130mm*130mm |
| Pixel Size | 85μm |
| Resolution | 1536*1536 |
| Frame Rate | 20fps |
| Table | |
|---|---|
| Size | 420mm*420mm |
| Detectable Area | 400mm*400mm |
| Max Load | 15kg |
| Equipment | |
|---|---|
| Magnification | Geometry 150X | System 1500X |
| Inspection Speed | Max 3.0s/point |
| Dimensions | 1100mm (L) * 1000mm (W) * 1600mm (H) |
| Weight | 1000kg |
| Power Supply | AC110-220V 50/60HZ |
| Max Power | 1300W |
| Industrial PC | Intel I5 CPU, 8G RAM, 240GB SSD |
| Displayer | 24" HDMI LCD |
- Emergency Stop: Located next to operation position for immediate power cutoff
- Tube Protection: Software prevents leaving without closing X-ray tube
- Radiation Leakage: No leakage (international standard: ≤1μSv/h)
- Lead Glass Observation Window: Transparent lead glass window shields radiation to observe internal status
- Window and Back Door Safety Interlock: X-ray tube powers off immediately when window or door opens
Using mouse to click the X button can turn on or off the X-ray.
Indicates the interlock status, pre-heat status, and X-ray status by flashing alternately red and green.
The brightness, contrast and gain of the image can be adjusted freely to achieve a satisfactory result.
Users can save the inspection parameters such as Z-axis position, and can directly call the parameters.
The table will move to the place you click and display on the screen.
Display real-time coordinates.
The measurement results (voids rate, distance, area, etc., set by users) display in order.
The movement speed of each axis can be adjusted to slow, normal and fast.
Automatic calculation - Click on two points to determine a rectangle.
Users can adjust the grayscale threshold, pixel and other parameters to get accurate results of automatic calculation.
Users can draw a polygon or a free figure and calculate it as a void into the void rate.
Users can save parameters such as grayscale threshold and can directly call the parameters.
| Function | Description |
|---|---|
| Distance | Click the A and B points to set as the baseline, then click the C point to measure the vertical distance |
| Distance Rate | Mostly used to measure the soldering rate of the through-hole |
| Angle | Click the A and B points to set as the baseline, then click the C point to measure the angle between the BA and BC rays |
| Radius | Click three points to determine a circle and measure the circumference, area and radius |
| Perimeter | Click two points to determine a square, measure the length, width and area |
| Mode | Description |
|---|---|
| Manual Setting | Users can set any positions on the table as inspection points, the software will automatically inspect and save the picture |
| Array | Users only need to set two of the inspection points and the number of rows and columns |
| Automatic Identification | For inspection points with obvious features, the software automatically identifies the positions, takes measurements, and saves the image |
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.