SSchneider ELAU VPM01D16AA00 PacDrive PS-4/10/16/230/00 16A 230V Power Supply

Product Overview

The Schneider ELAU VPM01D16AA00 is a PacDrive M PS-4 system power supply corresponding to the technical designation PS-4/10/16/230/00 and ELAU material number 13130258. It is designed to supply the DC intermediate circuit, 24 VDC control power and SERCOS communication required by compatible PacDrive SCL integrated servo modules.

The PS-4 is a system power-supply module rather than a servo drive, PLC controller or servo motor. It accepts a 220-240 VAC single-phase or three-phase mains input and provides a regulated DC bus and auxiliary 24 VDC output for the connected SCL servo system.

VPM01D16AA00 is the complete commercial reference. The PS-4/10/16/230/00 designation identifies the common hardware platform, while the final VPM suffix may identify firmware or a factory-specific configuration. The full commercial reference must therefore be retained when selecting a replacement.

Main Features

• Exact commercial reference: VPM01D16AA00
• Technical designation: PS-4/10/16/230/00
• ELAU material number: 13130258
• PacDrive M SCL system power supply
• Single-phase or three-phase 220-240 VAC mains input
• 20 A main input rating
• 325 VDC intermediate-circuit output
• 10 A continuous DC bus output
• 18 A peak DC bus output
• 24 VDC, 13 A auxiliary output
• Approximately 5 kW continuous power capacity
• Approximately 10 kW peak power capacity
• Integrated SERCOS communication
• Designed for compatible SCL integrated servo modules
• Legacy PacDrive replacement and maintenance product

Technical Specifications

Compatible System and Applications

The VPM01D16AA00 is intended for PacDrive M machine systems using compatible SCL integrated servo modules. Typical applications include packaging machinery, filling and sealing equipment, labeling machines, printing and converting systems, food-processing machinery, material-handling equipment and synchronized production machines.

The PS-4 supplies the common DC intermediate circuit and 24 VDC control voltage required by the SCL system. The actual number of connected SCL modules depends on motor size, machine duty cycle, acceleration requirements, simultaneous-axis loading, regenerative energy and the complete electrical design.

System compatibility must be confirmed from the installed SCL models, PacDrive controller, SERCOS topology, machine project, mains configuration and power calculation. The published maximum number of connected modules must not be used as a substitute for an application-specific power calculation.

Maintenance and Replacement Notes

Before replacing the power supply, verify the complete VPM commercial reference, technical model, ELAU material number, firmware, hardware revision and machine project. Do not identify the unit only as PS-4 because several firmware and special-configuration suffixes exist on the same hardware platform.

Check whether the original mains supply is single-phase or three-phase. Verify the incoming voltage, circuit protection, mains filter, protective earth, DC bus wiring, 24 VDC wiring, SERCOS connection and all SCL branch connections before installation.

Inspect the connected SCL modules and cables for DC bus faults, short circuits, damaged insulation or excessive regenerative loading before installing a replacement PS-4. A failed downstream module or cable can damage the replacement power supply.

The full suffix must be matched whenever possible. Firmware and special-configuration variants should not be considered automatically interchangeable, even when they share the PS-4/10/16/230/00 technical designation.

Related Models

Related PS-4 commercial references include VPM01D16AA20, VPM01D16AL00, VPM01D16AL03, VPM01D16AL12, VPM01D16AL22, VPM01D16AP00 and VPM01D16AQ22.

VPM01D16AL00 is associated with the V00.16.X firmware family, VPM01D16AP00 is associated with the V00.20.X firmware family, and VPM01D16AQ22 is associated with the V00.22.X firmware family and special configuration 22. References ending in AA20, AL03, AL12, AL22 or AQ22 may include machine-specific or factory-specific configurations whose exact functions must be confirmed from the original nameplate and machine documentation.

PS-5 power supplies belong to the related PacDrive iSH system but are not direct replacements for PS-4. PS-4 is intended for SCL systems, while PS-5 is intended for PacDrive iSH distributed servo systems.

Inquiry and Supply Notes

Please provide clear photographs of the complete nameplate, front panel and all electrical connectors when requesting a quotation. Also provide the connected SCL module models, PacDrive controller model, mains configuration and machine-project information.

The exact commercial reference, firmware, special configuration, hardware revision, product condition, testing status, included connectors, availability and delivery time must be confirmed before quotation.