A10VSO140DR/32L-PPB22U00 A10VSO140DG/32L-PPB22U99 A10VSO140DG/32L-PPB22U00 Original Rexroth Industrial Variable Displacement Piston Pump from Germany
Price:
1
MOQ:
1
Delivery Time:
negotiation
Brand:
Rexroth
Product Description
A10VSO140DR/32L-PPB22U00 A10VSO140DG/32L-PPB22U99 A10VSO140DG/32L-PPB22U00 Original Rexroth Industrial Variable Displacement Piston Pump from Germany
Product Specifications
Displacement
45 cm³
Pump Type
Piston Pump
Warranty
1 Year
Place of Origin
Fujian, China
Max. Horsepower
5 HP
Operating Pressure
350 bar
Maximum Flow Rate
117 L/min
Power (W)
75 W
Pressure
28 Mpa
Nominal Pressure
280 bar
Maximum Pressure
350 bar
Displacement, Geometric, per Revolution
45 cc
Case Volume
1.0 L
Rotational Speed (Maximum)
2600 rpm
Power
55 KW
Torque
200 Nm
A10VSO71DFLR/31R-PPA12N00
A10VSO71DR/31R-VPA42N00
A10VSO45DFR1/31R-PPA12N00
A10VSO45DFLR/31R-PPA12N00
A10VSO45DR/31R-VPA12N00
A10VSO45DFLR/31L-VPA12N00
A10VSO71DG/31R-PPA42N00
A10VSO71DFR/31R-PPA12N00
A10VSO71DFR/31R-PPA42N00
A10VSO71DFR1/31R-PPA42N00
A10VSO28DFLR/31L-VPA12N00
A10VSO28DRG/31L-VPA12N00
A10VSO28DFR1/31R-VPA12N00
A10VSO28DR/31R-VPA12N00
A10VSO28DFLR/31R-PPA12N00
A10VSO28DFR/31R-PPA12N00
A10VSO28DR/31R-PPA12N00
A10VSO28DG/31L-PPA12N00
A10VSO28DFLR/31R-VPA12N00
A10VSO28DFR1/31R-VPA12N00
A10VSO28DRG/31R-PPA12N00
A10VSO28DG/31R-PPA12N00
Frequently Asked Questions
1. Preventive Maintenance & Component Care
1.1 What is the correct way to replace the pump's shaft seal?
Improper seal replacement causes 60% of post-maintenance leaks. Follow this process: 1) Lock out the motor and drain the system. 2) Remove the coupling and use a seal puller to extract the old seal (avoid scratching the shaft). 3) Clean the seal housing and apply a thin layer of Rexroth R901287456 grease to the new seal's lip. 4) Press the seal in evenly using a socket (same diameter as the seal outer ring) to prevent distortion. 5) Reassemble and run the pump at low speed for 10 minutes--check for leaks.
1.2 How to extend the life of the pump's swashplate and bearings?
Swashplate and bearings are critical wear components. Maintenance tips: 1) Maintain oil temperature between 30-50°C--install a thermostatic valve to bypass the cooler when oil is cold (avoids dry wear). 2) Use only Rexroth's recommended oil (e.g., Shell Tellus S46) to ensure proper lubrication of the swashplate's sliding surface. 3) Replace the bearing assembly every 8,000 hours (even if no damage is visible)--use genuine part R900507641. 4) Avoid sudden load changes: Program the control system to ramp pressure up/down over 2 seconds to reduce impact on the swashplate.
Similar Products
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.
Company
Xiamen Lang Ye Hydraulic Electromechanical Equipment Co., Ltd
Location
Xia'Men City, China
Contact Person
zixin