aluminum electrolytic capacitor CapXon HP681M250N410A with 680 microfarad capacitance and 250 volt rating
Price:
Negotiable
MOQ:
Negotiable
Delivery Time:
Negotiable
Product Description
Product Overview
The CapXon HP series aluminum electrolytic capacitors are designed for reliable performance in various electronic applications. These capacitors offer a wide operating temperature range and are built to meet stringent quality standards, including JIS-C-5101-1. They are suitable for general-purpose use where stable capacitance and low leakage current are required. The product features a safety vent for overpressure protection and is manufactured in compliance with environmental regulations.
Product Attributes
- Brand: CapXon
- Origin: Shenzhen, China
- Series: HP
- Compliance: RoHS, Montreal Protocol
- Standards: JIS-C-5101-1, JIS-C-5102-4, JIS-C-5102-18
Technical Specifications
| Part Number | Capacitance (F) | Capacitance Tolerance (%) | Rated Working Voltage (VDC) | Surge Voltage (VDC) | Max. Dissipation Factor (%) | Ripple Current (120Hz /105) (A) | Max. Leakage Current (A) | Max. ESR (120Hz /20) (m) | Operating Temperature (C) | Case Size (D* L mm) | Endurance /105 (Hrs) |
|---|---|---|---|---|---|---|---|---|---|---|---|
| HP681M250N410A | 680 | -20~20 | 250 | 288 | 15 | 2.2 | 1237 | 290 | -40~105 | 25X41 | 2000 |
Technical Data
Electrical Characteristics
| Item | Conditions | Criterion |
|---|---|---|
| Operating Temperature Range | -40~105 (C) | |
| Capacitance | Temp: 202, Freq: 120Hz, Voltage: 0.5Vrms | Tolerance: -20~20% |
| Dissipation Factor (tan) | Temp: 202, Freq: 120Hz, Voltage: 0.5Vrms | See Table 1 |
| Leakage Current | Rated voltage applied for 5 min with 100010% protective resistor. | I3* CV () |
| Terminal Strength (Tensile) | Load applied in lead direction for 101S. | Terminal should not be loose, breakage and bad connected. |
| Lead Diameter (mm) | Gravity (N) | Weight (Kg) |
| 0.35d0.5 | 5 | 0.51 |
| 0.5d0.8 | 10 | 1.02 |
| 0.8d1.25 | 20 | 2.04 |
| SNAP-IN Type | 40 | 4.08 |
| Terminal Strength (Bending) | Static load applied to lead wire, bent 90 and returned, then bent 90 in opposite direction and returned. Approx. 2~3 sec per cycle. | Terminal should not be loose, breakage and bad connected. |
| Lead Diameter (mm) | Gravity (N) | Weight (Kg) |
| 0.35d0.5 | 2.5 | 0.25 |
| 0.5d0.8 | 5 | 0.51 |
| 0.8d1.25 | 10 | 1.02 |
| LUG Terminal | 20 | 2.04 |
| (SNAP-IN type not tested for bending) | ||
| Temperature Characteristic | Measured after thermal equilibrium, impedance at same frequency. | 1. Impedance ratio shall not exceed values in Table 2. 2. Leakage current Shall not more than 800% of initial specified value. |
| Step | Temperature | Item |
| 1 | 202 | Impedance |
| 2 | Lower Category Temp 3C | Impedance |
| 3 | Upper Category Temp 2C | LC |
| High Temperature Load | Temp: 105, Applied Voltage: Rated DC working voltage, Test Time: 2000 H. Tested after 16 hours in standard atmospheric conditions. | 1. Capacitance Change: C/C 10% 2. Dissipation Factor: DF 130% of initial value 3. Leakage Current: LC initial value 4. Appearance: No visible damage. |
| High Temperature Exposure (Storage) | Temp: 105, Applied Voltage: None, Test Time: 1000H. Tested after 16 hours in standard atmospheric conditions. Pre-treatment: 30 min DC working voltage. | 1. Capacitance Change: C/C 10% 2. Dissipation Factor: DF 130% of initial value 3. Leakage Current: LC initial value 4. Appearance: No visible damage. |
| Surge Test | Temp: 15~35, Applied Voltage: 288V. Cycle: 30s charge, 330s discharge. Cycles: 1000. Tested after 16 hours in standard atmospheric conditions. | 1. Capacitance Change: C/C 15% 2. Dissipation Factor: DF initial value 3. Leakage Current: LC initial value 4. Appearance: No visible damage. |
| Vibration | Freq: 10~55Hz, Amplitude: 0.75mm, Accel: 98 m/s (10g). Time: X, Y, Z directions each 2 Hrs (total 6 Hrs). Tested within 30 minutes after vibration. | 1. Capacitance Change: C/C 5% 2. Dissipation Factor: DF initial value 3. Leakage Current: LC initial value 4. Appearance: No visible damage. |
| Solderability | Solder: Sn96.5%, Ag3%, Cu0.5%. Temp: 2455, Immerse Time: 2.00.5S. Speed: 252.5mm/s. Depth: 1.5~2.0mm between body and solder. Tested after 2 hours out of solder stove. | New solder adhesion > 95%. |
| Resistance to Soldering Heat | Solder: Sn96.5%, Ag3%, Cu0.5%. Temp: 2600~3, Immerse Time: 101S. Speed: 252.5mm/s. Depth: 1.5~2.0mm between body and solder. Tested after 2 hours out of solder stove. | 1. Capacitance Change: C/C 5% 2. Dissipation Factor: DF initial value 3. Leakage Current: LC initial value. |
| Vent Test (for products with vent requirement) | Method: Reverse Voltage 80V or Over Voltage (1.5x Rated Voltage). | No explosion, flash, flame, spark, or fire. If vent doesn't operate for 30 min, test passed (only for overvoltage method). |
| Temperature Cycling | Refer to JIS-C-5101-1 (2010) No:4.16. 10 cycles. | 1. Capacitance Change: C/C 5% 2. Dissipation Factor: DF initial value 3. Leakage Current: LC initial value 4. Appearance: No visible damage. |
| Step | Temp | Time (Min) |
| 1 | Lower Category Temp 3C | 303 |
| 2 | 255 | 3 |
| 3 | Upper Category Temp 2C | 303 |
| 4 | 255 | 3 |
| High Temp and Humidity | Temp: 402, Humidity: 90~95%RH, Time: 250H. Tested after 16 hours in standard atmospheric conditions. | 1. Capacitance Change: C/C 20% 2. Dissipation Factor: DF 1.2 times initial value 3. Leakage Current: LC initial value 4. Appearance: No visible damage. |
Marking Explanation
Example:
- (1) CapXon: Brand
- (2) 250V: Rated Voltage
- (3) 680F: Nominal Capacitance
- (4) (-) : Polarity (Cathode Indicate)
- (5) 105: Maximum Operating Temp.
- (6) HP: Series
- (7) VENT: Safety Vent
Marking Example: 680uF-250V HP VENT 105C *-NEG CapXon
Characteristic Tables
Table 1: Dissipation Factor (DF)
| F/Vdc | 6.3 | 10 | 16 | 25 | 35 | 50 | 63 | 80 | 100 | 160~420 | 450~600 | 8200 | 10000 to 22000 | 27000 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| DF (%) | - | 35 | 35 | 30 | 25 | 20 | 20 | 15 | 15 | 15 | 20 | 100 | 55 | 60 |
| 40 | 50 | 50 | ||||||||||||
| 40 | 40 | 40 | ||||||||||||
| 35 | 35 | 35 | ||||||||||||
| 30 | 30 | 30 | ||||||||||||
| 25 | 25 | 25 | ||||||||||||
| 15 | 15 | 15 |
Table 2: Impedance Ratio (Z-25C / Z 20C and Z-40C / Z 20C)
| Impedance ratio max | VR(V) | 6.3~16 | 25 | 35 | 50~100 | 160~250 | 300~350 | 400~550 |
|---|---|---|---|---|---|---|---|---|
| Z-25 / Z 20 | 4 | 3 | 3 | 3 | 4 | 8 | 8 | |
| Z-40 / Z 20 | 15 | 10 | 8 | 6 | 8 | 12 | - |
Table 3: Multiplier for Ripple Current vs. Frequency
| VR(V)/Frequency(Hz) | 50(60) | 120 | 300 | 1K | 10K | 50K-100K |
|---|---|---|---|---|---|---|
| 10VR100 | 0.88 | 1 | 1.07 | 1.15 | 1.15 | 1.15 |
| 160VR250 | 0.81 | 1 | 1.17 | 1.32 | 1.45 | 1.5 |
| 315VR600 | 0.77 | 1 | 1.16 | 1.30 | 1.41 | 1.43 |
Important Notes:
- Specifications are subject to change without notice.
- Operating conditions may affect capacitor lifetime; consult Capxon for lifetime calculations.
- For aerospace, , life-saving, or life-sustaining applications, consult Capxon before design-in.
- Capxon does not warrant suitability for buyer's intended application; buyer is responsible for verification and product selection.
- Capxon disclaims all warranties other than express written warranties.
- Further information is available on www.capxongroup.com.
Similar Products
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.
Company
Beijing Silk Road Enterprise Management Services Co., Ltd.
Location
16 Floor, Unit B, Jiatai International Mansion, No 41, Dongsihuan Zhong Road, Chaoyang District, Beijing
Contact Person
Sellina