Versatile potentiometer CTR C6066G-CE10H5.0-B103-005 designed for resistance control in electronics

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

C6066G Series General Specification

This specification applies to the C6066G model, a potentiometer designed for various applications requiring precise resistance control. It offers a nominal total resistance of 10K 20% with a B Taper (linear) resistance law. The product is built to withstand operating temperatures from -10 to 70 and storage temperatures from -30 to 70. It is suitable for applications demanding reliable electrical and mechanical performance, including volume control and signal attenuation.

Product Attributes

Brand: Not specified
Origin: Not specified
Material: Not specified
Color: Not specified
Certifications: Not specified

Technical Specifications

Item	Conditions	Specifications
Scope	Model C6066G type	This specification applies to model C6066G type
Operating temperature range		-1070
Storage temperature range		-3070
Test conditions (Standard atmospheric conditions)	Ambient temperature: 535 Relative humidity: 4585 Air pressure: 86106kpa	Unless otherwise specified, the standard range of atmospheric conditions for making measurements and test is as follows:
Test conditions (Base conditions)	Ambient temperature: 202 Relative humidity: 6070 Air pressure: 86106kpa	If there is any doubt about the results, measurements shall be made within the following limit:
Nominal total resistance and tolerance	Resistance between terminals 1 and 3	10K20%
Resistance law	Measurement shall be made by the resistance law method. Refer to JISC5261 standard.	B Taper (Linear)
Power rating	Continuous full load operation at the maximum voltage between terminals 1 and 3. Curve of power rating vs. ambient temperature is shown in the graph.	0.1W
Residual resistance	Contact brush stop at the end of the travel of effective rotation (A). Measured between terminals 1 and 2, and terminals 2 and 3.	R1.210
Maximum attenuation	15A, B(1B): Lever set to term.1 side end. 15C: Lever set to term.3 side end. Measured when voltage is applied to term.1-3.	15A, B(1B): Not specified 15C: Not specified
Rated voltage		150V AC
Maximum operating voltage		Not specified
Sliding noise	DC 20V applied between terminals 1-3 (rated voltage 20V, apply by rated voltage). Traveling speed: 1 cycle/3sec.	Less than 60mVp-p
Insulation resistance	DC 250V applied for 1 min between individual terminals and frame/shaft.	100M or more
Dielectric strength	300V AC for 1 minute between individual terminals and frame/shaft. Measuring frequency: 50~60Hz; Trip current: 2mA.	Electrical characteristics shall be satisfied with specification
Gang error	Dual: For volume contract -40~0dB 3dB or less	3dB or less
Total travel slide	Effective slide travel.	600.5mm
Sliding force	Rotational speed: Not specified. Standard atmospheric conditions (5C to 35C).	10~80gf
Shaft stop strength	A static load of 5Kgf applied at 5mm from the top surface of the lever for 10 sec.	Electrical characteristics shall be satisfied with specification
Shaft push & pull strength	A static load of 5Kgf applied to the shaft in vertical axial directions for 101 seconds.	Shaft without damage, rotational torque without abnormality. Electrical characteristics shall be satisfied with specification.
Lever wobble	A torsion moment of 250gf.cm applied at the lever in a direction perpendicular to the axial direction. L is the length between mounting surface and test point.	Less than 2(2*L/20)mm
Lever inclination and torsion		Less than 2
Distance from lever to the middle of the mounting screw hole	Measured at both ends.	0.5mm or less on each end
Terminal strength (After soldering)	A static load of 0.5kgf applied to the terminals for 10s in any direction.	Without functional problem because of rickety terminals or poor contact.
Solder ability	Terminals immersed into solder bath at 2605C for 30.5s. Solder shall cover 75% minimum of the surface being immersed.
Resistance to soldering heat	Subjected to soldering. PCB: 1.6mm thickness single-sided copper clad laminated phenol. Solder flux: Flux of 0.82 specific weight in bubbling type. Preheating: Substrate surface temperature within 100C in one minute. Wave Soldering: Temperature 2605C, Application time 5 1 sec. Hand Soldering: Bit temperature 35010C, Application time within 3 s.	Change in total resistance: 5%. Without visual deformation or terminal loosing. Electrical characteristics shall be satisfied with specification.
Resistance to heat	Stored at 702C for 2408h. Measured after maintaining at standard atmospheric conditions for 1h.	Change in total resistance: +5/-30%
Resistance to cold	Stored at -302C for 1204h. Measured after maintaining at standard atmospheric conditions for 1h.	Change in total resistance: 20%
Damp heat	Stored at 402C, with relative humidity of 90% to 95% for 964h. Measured after maintaining at standard atmospheric conditions for 1h.	Noise: Less than 150mV p-p. Change in total resistance: +35/-5%
Change of temperature	Subjected to 5 successive cycles of temperature as shown in table. Measured after maintaining at standard atmospheric conditions for 1h.	Change in total resistance: 20%. Rotational noise: Less than 150mV p-p.
Endurance	Moving contact rotated from one end stop to the other and returned to original position. 600 cycles per hour. 15000200 cycles.	Change in total resistance: 15%. Rotational noise: Less than 150mV p-p. Dielectric strength: without damage, deformation, breakdown. Appearance: molded part without deformation or cracks.