Pb Free Frequency Control Quartz Crystal HELE X2C038400BA1H-HZ 38.4 MHz with RoHS and REACH Certification
Price:
Negotiable
MOQ:
Negotiable
Delivery Time:
Negotiable
Product Description
Product Overview
The HSX211S Quartz Crystal from Harmony Electronics Corporation is a high-performance frequency control component designed for various electronic applications. It offers precise frequency stability and reliability, adhering to stringent environmental and mechanical standards. This product is Pb-free, RoHS compliant, HF-Halogen free, and REACH compliant, making it an environmentally conscious choice for modern electronics manufacturing.
Product Attributes
- Brand: Harmony Electronics Corporation
- Product Type: Quartz Crystal
- Model: HSX211S
- Origin: Taiwan
- Certifications: Pb free, RoHS Compliant, HF-Halogen free, REACH Compliant
- MSL Level: 1
Technical Specifications
| Specification | Value | Unit | Notes |
|---|---|---|---|
| Nominal Frequency | 38.400000 | MHz | |
| Frequency (FL) | 38.400000 | MHz | |
| Mode of Oscillation | Fundamental | ||
| Frequency Tolerance | -10 to +10 | ppm | at 253 |
| Equivalent Resistance (RR) | 50 | SERIES | |
| Storage Temperature Range | -40 to +105 | ||
| Operable Temperature Range | -30 to +85 | ||
| Temperature Stability | -10 to +10 | ppm | -30~ +85 |
| Loading Capacitance (CL) | 10.0 | pF | |
| Drive Level (DL) | 10 to 100 | W | |
| Shunt Capacitance (C0) | 2.0 | pF | |
| Insulation Resistance | 500 | M | at DC 100V |
| Aging | -3 to +3 | ppm/Year | |
| Circuit Measurement | Measured in HP/E5100A,S&A 250B | ||
| Dimensions (Length x Width) | 1.65 x 2.05 | mm | |
| Dimensions (Height) | 0.7 | mm | |
| Land Pattern Layout (Length x Width) | 1.1 x 1.4 | mm | |
| Pin Connections | #1 Crystal, #2 Crystal, #3 GND/Lid, #4 GND/Lid | ||
| Inside Structure - Base Material | Ceramic Al2O3 | ||
| Inside Structure - Lid Material | Metal Fe- Ni Co Ni Plating | ||
| Inside Structure - Kovar Material | Metal Fe- Ni -Co | ||
| Inside Structure - Crystal Blank Material | Quartz SiO2 Rectangular At-Cut | ||
| Inside Structure - Electrode Material | Metal | ||
| Inside Structure - PAD Material | Metal W Ni Plating Au Plating | ||
| Inside Structure - Connective Adhesive | Silver Powder Ag | ||
| Carrier Tape Width | 8.0 | mm | 0.2 |
| Carrier Tape Pitch | 4.0 | mm | 0.1 |
| Reel Quantity | 1000 or 3000 | pcs | |
| Standard Packing Quantity | 3000 | PCS / REEL | |
| Shock Test | Dropping from 120 cm height 3 times on 30 mm Concrete floor. | Refer to: JIS C 60068-2-32 | |
| Vibration Test | Frequency 10-55Hz, Sine Wave full amplitude of 0.8mm to X, Y and Z 3 axes, 2 cycles and duration of 2 hours to each direction. | Refer to: JIS C 60068-2-6/ MIL-HDBK-781A 6.5.2 | |
| Leakage Test Leak Rate | 1.0x10-9 | Pa-m3/sec. Max. | Measured by Helium leak detector. Refer to: JIS C 60068-2-17 |
| Solder ability | Dipping in solder bath at 245deg.C 5deg.C for 3 0.5 sec. | Refer to: JIS C 60068-2-20/ JIS C 60068-2-58 | |
| Bending Strength Test | Apply Pressure to the center of board until it is bent to 3 mm and hold for 5 1 sec. Pressure speed: 0.5 mm/sec. | Refer to: EIAJ ET-7403/ JIS C 60068-2-21 | |
| Adhesion Test | Apply pressure vertically to the side of specimen attached to the circuit board with the pressure jig. Pressure: 5N for 101 sec. | Refer to: EIAJ ET-7403/ JIS C 60068-2-21 | |
| Body Strength Test | Apply pressure to the center of body with the R0.5 pressure jig. pressure : 5N for 101sec | Refer to: EIAJ ET-7403 JIS C 60068-2-21 | |
| Resistance of Soldering Heat | Performing as the following reflow | Refer to: JIS C 60068-2-58 | |
| Humidity Test | Temperature 602, RH 90~95%, duration of 240 hours. | Back to room temperature first, then check the component after 1~2 hours. Refer to: JIS C 60068-2-3 | |
| Storage in Low Temperature | -40deg.C 2deg.C, duration of 240 hours. | Back to the room temperature first, then check the component after 1~2 hours. Refer to: JIS C 60068-2-1 | |
| Storage in High Temperature | +85deg.C 2deg.C, duration of 240 hours. | Back to the room temperature first, then check the component after 1~2 hours. Refer to: JIS C 60068-2-2 | |
| Thermal Shock Test | -55deg.C 2deg.C (30min) +125deg.C 2deg.C (30min) 25 cycles. Temperature Increasing/reducing time3mins. | Back to the room temperature first, then check the component after 1~2 hours. Refer to: JIS C 0025 |
Similar Products
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.
Company
Beijing Silk Road Enterprise Management Services Co., Ltd.
Location
16 Floor, Unit B, Jiatai International Mansion, No 41, Dongsihuan Zhong Road, Chaoyang District, Beijing
Contact Person
Sellina