Durable Hongda RXF-1/4W-3.9R-J-T52 resistor designed for consistent fusing in electronic equipment
Price:
Negotiable
MOQ:
Negotiable
Delivery Time:
Negotiable
Product Description
Product Overview
The RXF series from Dongguan Hongda Electronic Technology Co., Ltd. are high-performance resistors designed for a wide range of electronic applications. These resistors offer excellent surge resistance, good fusing consistency, and a compact size for easy installation, ensuring safety and reliability. They are widely used in electronic equipment such as light sources, switching power supplies, chargers, and home appliances.
Product Attributes
- Brand: RXF Series
- Manufacturer: Dongguan Hongda Electronic Technology Co., Ltd.
- Origin: China
- Certifications: VDE (Certificate No.: 40036858), UL/CUL (Certificate No.: E359590), CQC (Certificate No.: 0.5W-CQC13001095211, 1W-CQC13001095213, 2W-CQC13001095221)
Technical Specifications
Dimensions and Lead Lengths
| Model | Rated Power (W) | Dimensions (mm) | Allowable Lead Length* (mm) | Dmax. | Lmax. | H1 | d0.05 |
|---|---|---|---|---|---|---|---|
| RXF 0.25, 0.5S, 1WX | 3.0 | 7.0 | 6070 | 0.380.45 | 1 | ||
| 0.5, 1S, 2WX | 4.0 | 10.0 | 6090 | 0.430.60 | 1.5 | ||
| 1, 2S, 3WX | 5.0 | 12.0 | 6070 | 0.540.72 | |||
| 2, 3S | 6.0 | 16.0 | 6080 | 0.600.72 |
Electrical Characteristics
| Model | Rated Power (W) | Resistance Range () | Resistance Tolerance (%) | Insulation Voltage (V) (DC or AC peak) | Component Limit Voltage (V) |
|---|---|---|---|---|---|
| RXF 0.25, 0.5S, 1X | 0.22-300 | 5, 10 | 250 | 200 | |
| 0.5, 1S, 2X | 250 | 350 | |||
| 1, 2S, 3X | 350 | 350 | |||
| 2, 3S | 0.22-47 | 500 | 350 |
General Data
| Parameter | Specification |
|---|---|
| Nominal Resistance Tolerance | 5%, 10% |
| Climatic Category | 55/155/21 |
| Low Air Pressure | 8.5kpa |
| Stability Grade | 5% |
| Limit Resistance Variation | Long-term test: (5%R+0.1); Short-term test: (1%R+0.05) |
| Temperature Coefficient | Standard type 350 ppm; Semi-fusing type, explosion-proof type, high lightning surge type: 35001500 ppm |
| Rated Current | I2(A)=P(W)/R() |
| Power Derating Curve | Refer to Figure 2. Rated power is the maximum continuous operating value at 70. Power consumption decreases according to the curve when exceeding 70. |
| Fusing Characteristic | Defined as significant increase in resistance when subjected to specified overload, causing current to drop below 1/50 of initial test current. Fusing time is the time from applying overload to fusing. |
| Fusing Time Requirements | Under specified rated current overload multiples, fusing time should comply with tables. (See Table 3-1 for standard and high lightning surge types; Table 3-2 for explosion-proof types; Table 3-3 for semi-fusing types). Fusing time can be custom-made per user requirements. |
| Impact Resistance | Test according to Figure 3. Repeatedly switch K1 ON for 2S and OFF for 2S for 100 cycles. Test resistor should not be open-circuited. (Capacitance C selection based on customer requirements, default C=10uF. Resistance R selection based on circuit, converted to internal resistance, R power rating 20W, power factor 0.8, for resistors under 10W generally take 20W, 5.1K(5%)). |
Main Test Items, Methods, and Performance Requirements
| No. | Test Item | Test Method | Performance Requirements |
|---|---|---|---|
| 1 | Resistance | Measured by resistance error sorter. | Resistance value within nominal resistance and allowable tolerance. |
| 2 | Short-time Overload | Apply 2.5 times rated voltage for 5S, recover 1-2h, measure resistance and calculate variation rate. | Resistance variation: R(2%R+0.05) |
| 3 | Solderability | Dip lead ends in solder pot at (2605) for 20.5S, depth 2+0/-0.5mm from body. Observe solder coverage. | Over 90% surface coverage in circumferential direction of dipped part. |
| 4 | Voltage Proof | Place resistor in metal 'V' groove, apply specified insulation voltage between lead wires and 'V' groove for 60S. | No visible damage, clear marking; no breakdown, arcing. |
| 5 | Resistance to Soldering Heat | Dip lead ends in solder pot at (35010) for 3.50.5S, depth 2+0/-0.5mm from body. Recover 1h, measure resistance and calculate variation rate. | Resistance variation: R(1%R+0.05) |
| 6 | Rapid Change of Temperature | Cycles of low temp (-553) for 30min, normal temp 2-3min, high temp (1553) for 30min, normal temp 2-3min. Perform 5 cycles, recover 1-2h, measure resistance and calculate variation rate. | Resistance variation: R(1%R+0.05) |
| 7 | Endurance | Place in constant temperature oven at (703), apply rated DC voltage, 1.5h ON, 0.5h OFF cycle for 1000h. Recover 1-4h, measure resistance and calculate variation rate. | Resistance variation: R(5%R+0.1) |
| 8 | Lead Strength | Tensile: 10N for 10S; Bending: Apply 5N load, tilt body approx. 90 in 2-3S, recover, bend in opposite direction (2 bends total). | Resistance variation: R(1%R+0.05) |
| 9 | Vibration | Resistor body 61mm from mounting point. Vibration frequency 10-500Hz, amplitude 0.75mm or acceleration 98m/s (whichever is smaller). Vibration direction Z, X, Y axes for 2h each (total 6h), period 1min (10-55-10Hz). Measure resistance and calculate variation rate after test. | 1) Appearance: No mechanical damage. 2) Resistance variation: R(1%R+0.05) |
| 10 | Climatic Sequence | Dry heat; Cyclic damp heat (Test Db, 1st cycle); Cold; Low pressure; Cyclic damp heat (Test Db, remaining cycles); DC load. | Resistance variation: R(5%R+0.1). Insulation Resistance: 100M. |
| 11 | Accidental Overload | Install sample in single-layer wire mesh cylinder 253mm from resistor body. Apply 5, 10, 16 times rated power overload for 5min or until open circuit. | Wire mesh cylinder does not ignite. |
Taping and Packaging
| Taping Specification | Dimensions (mm) | U | W | P | L1-L2 | T | Z | R | t | T26 |
|---|---|---|---|---|---|---|---|---|---|---|
| 381 | 260.5 | 50.5 | 0.5 | 60.1 | 1 | 0 | 3.2 | 1.5 | ||
| T52 | 642 | 521 | 1 | |||||||
| T63 | 752 | 631 | 100.5 | 1.2 | ||||||
| T72 | 842 | 722 | 50.5 | 1.2 |
Sleeve Product Specifications
| Shape | Dimensions (mm) | H1 | H11.5 | H21.5 | hh (15%) | h12 | h22 |
|---|---|---|---|---|---|---|---|
| TA Type | 70 | 20 | 20 | 50 | 10 | 10 | |
| TB Type | 80 | 5 | 25 | 40 | 10 | 30 |
Note: 1. Tolerance for exposed lead length 5 mm is +2/-1 mm. 2. Sleeve dimensions can be custom-made per customer requirements.
Molded Product Specifications
| Shape | Dimensions (mm) | P1.0 | H1 | h0.5 |
|---|---|---|---|---|
| n Type | 5 | 3.5 | 8 | 3.5 |
| B Type | 5 | 3.5 | 8 | 3.5 |
| L Type | 12.5 | 4.5 | 14.5 | 5.5 |
Note: Molded shape and dimensions can be custom-made per customer requirements.
Model Specification Naming Convention (Example)
| Component | Description |
|---|---|
| RXF | Series Name |
| Rated Power | 0.25w, 0.5w, 1w, 2w, 3w |
| S: Miniaturized, X: Ultra-miniaturized | Type |
| Resistance Tolerance | J: 5%, K: 10%, M: 20% |
| Nominal Resistance | E24 Series (See color code diagram) |
Color Code Marking Diagram
| Color | 1st Digit | 2nd Digit | 3rd Digit | Multiplier | Tolerance |
|---|---|---|---|---|---|
| Black | 0 | 0 | 0 | 10 | |
| Brown | 1 | 1 | 1 | 10 | 1% |
| Red | 2 | 2 | 2 | 10 | 2% |
| Orange | 3 | 3 | 3 | 10 | |
| Yellow | 4 | 4 | 4 | 10 | |
| Green | 5 | 5 | 5 | 10 | 0.5% |
| Blue | 6 | 6 | 6 | 10 | 0.25% |
| Violet | 7 | 7 | 7 | 10 | 0.1% |
| Gray | 8 | 8 | 8 | 10 | |
| White | 9 | 9 | 9 | 10 | |
| Gold | 10 | 5% | |||
| Silver | 10 | 10% | |||
| Plain | 20% |
Packaging Method
- Inner Box Packaging: Taped, 1K/box
- Outer Box Packaging: (Details not provided in source text)
Similar Products
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.
Company
Beijing Silk Road Enterprise Management Services Co., Ltd.
Location
16 Floor, Unit B, Jiatai International Mansion, No 41, Dongsihuan Zhong Road, Chaoyang District, Beijing
Contact Person
Sellina