Surge resistant Hongda RXF-1/2W-22R-J-T52 resistor suitable for chargers and switching power supplies
Price:
Negotiable
MOQ:
Negotiable
Delivery Time:
Negotiable
Product Description
Product Overview
The RXF series resistors from Dongguan Hongda Electronic Technology Co., Ltd. offer excellent surge resistance and good fusing consistency in a compact, easy-to-install design. These resistors are safe and reliable, widely used in electronic equipment such as light sources, switching power supplies, chargers, and home appliances. They have obtained VDE, UL/CUL, and CQC safety certifications.
Product Attributes
- Brand: RXF Series
- Manufacturer: Dongguan Hongda Electronic Technology Co., Ltd.
- Origin: China
- Certifications: VDE, UL/CUL (Certification No.: E359590), CQC (Certification Nos.: 0.5W-CQC13001095211, 1W-CQC13001095213, 2W-CQC13001095221)
Technical Specifications
Dimensions and Lead Lengths
| Model | Rated Power (W) | Dimensions (mm) Dmax. Lmax. | Lead Allowable Length* (mm) | H1 | d0.05 |
|---|---|---|---|---|---|
| RXF 0.25, 0.5S, 1WX | 3.0 | 7.0 | 6070 | 0.380.45 | 1 |
| 0.5, 1S, 2WX | 4.0 | 10.0 | 6090 | 0.430.60 | 1.5 |
| 1, 2S, 3WX | 5.0 | 12.0 | 6070 | 0.540.72 | |
| 2, 3S | 6.0 | 16.0 | 6080 | 0.600.72 |
Electrical Characteristics
| Model | Rated Power (W) | Resistance Range () | Resistance Tolerance (%) | Insulation Voltage (V) (DC or AC Peak) | Component Limit Voltage (V) |
|---|---|---|---|---|---|
| RXF 0.25, 0.5S, 1X | 0.22-300 | 5, 10 | 250 | 200 | |
| 0.5, 1S, 2X | 250 | ||||
| 1, 2S, 3X | 350 | ||||
| 2, 3S | 0.22-47 | 500 | 350 |
General Data
| Parameter | Value |
|---|---|
| Nominal Resistance Tolerance | 5%, 10% |
| Climatic Category | 55/155/21 |
| Low Air Pressure | 8.5kpa |
| Stability Grade | 5% |
| Limit Value of Resistance Change | Long-term test: (5%R+0.1); Short-term test: (1%R+0.05) |
| Temperature Coefficient | Standard type 350 ppm; Semi-fusing type, explosion-proof type, high lightning surge type: 35001500 ppm |
| Rated Current | I(A) = P(W)/R() |
| Power Derating Curve | Refer to Figure 2 (Rated power is maximum continuous operation at 70; derate according to curve above 70) |
| Fusing Characteristic | Defined as significant increase in resistance when subjected to specified overload, causing current to drop below 1/50 of initial test current. Fusing time is time from application of overload until fusing occurs. |
| Fusing Time Requirements | Under specified rated current overload conditions, fusing time meets table requirements. (See Tables 3-1, 3-2, 3-3 for details) |
| Impact Resistance | Test according to Figure 3: Repeatedly switch K1 ON/OFF 100 times (2S ON, 2S OFF). Resistor should not open circuit. (Capacitor C selection based on customer requirements, typically 10uF. Resistor R selection based on circuit, 20W power rating, 0.8 power factor, typically 20W for resistors under 10W, 5.1K5%) |
Main Test Items, Methods, and Performance Requirements
| No. | Test Item | Test Method | Performance Requirement |
|---|---|---|---|
| 1 | Resistance | Measured by resistance error sorter. | Resistance value within nominal resistance and allowable deviation. |
| 2 | Short-time Overload | Apply 2.5 times rated voltage for 5S, recover 1-2h, measure resistance, calculate resistance change rate. | Resistance Change: R(2%R+0.05) |
| 3 | Solderability | Dip lead ends into solder pot (2605) for 20.5S at depth 2+0/-0.5mm from body. Observe solder coverage. | Over 90% surface coverage in circumferential direction on dipped part. |
| 4 | Withstand Voltage | Place resistor in metal "V" groove, apply specified insulation voltage between leads and groove for 60S. | No visible damage, clear marking; no breakdown, arcing. |
| 5 | Withstand Soldering Heat | Measure resistance before test. Dip lead ends into solder pot (35010) for 3.50.5S at depth 2+0/-0.5mm from body. Recover 1h, measure resistance, calculate change rate. | Resistance Change: R(1%R+0.05) |
| 6 | Rapid Temperature Change | Cycle: Low temp (-553) (30min), Room temp (2-3min), High temp (1553) (30min), Room temp (2-3min). Repeat 5 cycles. Recover 1-2h, measure resistance, calculate change rate. | Resistance Change: R(1%R+0.05) |
| 7 | Endurance | Place resistor in constant temperature oven (703), apply rated DC voltage, 1.5h ON, 0.5h OFF cycle for 1000h. Recover 1-4h, measure resistance, calculate change rate. | Resistance Change: R(5%R+0.1) |
| 8 | Lead Strength | Tensile: 10N for 10S. Bending: Apply 5N load, tilt body approx. 90 in (2-3)S, then bend in opposite direction (2 bends total). | Resistance Change: R(1%R+0.05) |
| 9 | Vibration | Resistor body 61mm from mounting point. Vibration frequency 10-500Hz, amplitude 0.75mm or acceleration 98m/s (whichever is smaller). Directions Z, X, Y axes for 2h each (total 6h). Cycle: 1min (10-55-10Hz). Measure resistance after test, calculate change rate. | 1) Appearance: No mechanical damage. 2) Resistance Change: R(1%R+0.05) |
| 10 | Climatic Sequence | Dry heat - Cyclic damp heat (Test Db, 1st cycle) - Cold - Low pressure - Cyclic damp heat (Test Db, remaining cycles) - DC load. | Resistance Change: R(5%R+0.1). Insulation Resistance: 100M |
| 11 | Accidental Overload | Install sample in single-layer silk screen cylinder 253mm from resistor body. Apply 5, 10, 16 times rated power overload for 5min or until open circuit. | Silk screen cylinder does not ignite. |
Taping and Packaging
| Taping Specification | Dimensions (mm) U | W | P | L1-L2 | T | Z | R | t | T2 |
|---|---|---|---|---|---|---|---|---|---|
| T26 | 381 | 260.5 | 50.5 | 0.5 | 60.1 | 1 | 0 | 3.2 | 1.5 |
| T52 | 642 | 521 | 1 | ||||||
| T63 | 752 | 631 | 1.2 | 752 | 631 | 100.5 | |||
| T72 | 842 | 722 | 50.5 | 1.2 | 842 | 722 | 100.5 |
Sleeve Product Dimensions
| Shape | Dimensions (mm) H1 | H11.5 | H21.5 | hh (15%) | h12 | h22 |
|---|---|---|---|---|---|---|
| TA Type | 70 | 20 | 20 | 50 | 10 | 10 |
| TB Type | 80 | 5 | 25 | 40 | 10 | 30 |
Molded Product Dimensions
| Shape | Dimensions (mm) P1.0 | H1 | h0.5 |
|---|---|---|---|
| n Type | 5 | 3.5 | 8 |
| B Type | 5 | 3.5 | 8 |
| L Type | 12.5 | 4.5 | 14.5 |
| L Type | 5.5 |
Model Specification Naming (Example)
| Component | Description |
|---|---|
| Model | RXF |
| Rated Power | 0.25w, 0.5w, 1w, 2w, 3w |
| Resistance Tolerance | J: 5%, K: 10%, M: 20% |
| Nominal Resistance | E24 Series (See diagram) |
| Type | S: Miniaturized, X: Ultra-miniaturized |
Color Code Marking
| Color | 1st Digit | 2nd Digit | 3rd Digit | Multiplier | Tolerance |
|---|---|---|---|---|---|
| Black | 0 | 0 | 0 | 10 | |
| Brown | 1 | 1 | 1 | 10 | 1% |
| Red | 2 | 2 | 2 | 10 | 2% |
| Orange | 3 | 3 | 3 | 10 | |
| Yellow | 4 | 4 | 4 | 10 | |
| Green | 5 | 5 | 5 | 10 | 0.5% |
| Blue | 6 | 6 | 6 | 10 | 0.25% |
| Violet | 7 | 7 | 7 | 10 | 0.1% |
| Gray | 8 | 8 | 8 | 10 | |
| White | 9 | 9 | 9 | 10 | |
| Gold | 10 | 5% | |||
| Silver | 10 | 10% | |||
| Plain | 20% |
Packaging
- Inner Box Packaging: Taped, 1K/box
- Outer Box Packaging: Not specified
Similar Products
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.
Company
Beijing Silk Road Enterprise Management Services Co., Ltd.
Location
16 Floor, Unit B, Jiatai International Mansion, No 41, Dongsihuan Zhong Road, Chaoyang District, Beijing
Contact Person
Sellina