Quartz Crystal Resonator KYX KUS240001230 24 Megahertz Frequency with Wide Storage Temperature Range

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Overview

This document specifies the technical parameters for the HC-49SJJ/24.000MHZ Quartz Crystal Resonator manufactured by Shenzhen Kaiyuexiang Electronics Co., Ltd. It details the general, electrical, and mechanical specifications, as well as environmental endurance tests to ensure product reliability and performance.

Product Attributes

Brand: Kaiyuexiang
Origin: Shenzhen, China
Product Name: Quartz Crystal Resonator
Product Model: HC-49SJJ/24.000MHZ
Original Manufacturer Model: KUS240001230
Technical Department: Dong Zongquan

Technical Specifications

Parameter	Specification	Unit	Conditions
1. GENERAL
HOLDER TYPE	49US AT CUT
MODE OF VIBRATION	FUND S&A
OSCILLATION MODE	KH-1240
TEST FACILITIES
STORAGE TEMPERATURE	-40 TO +85
DRIVER LEVEL	100W
2. ELECTRICAL PARAMETER
NORMAL FREQUENCY	24.000	MHz
FREQUENCY TOLERANCE (252)	30	ppm	252
TEMPERATURE STABILITY	20	ppm
OPERATING TEMPERATURE RANGE	-20 TO +70
LOAD CAPACITANCE	12	PF
MOTIONAL CAPACITANCE	3	PF MAX
SHUNT CAPACITANCE
EFFECTIVE SERIES RESISTANCE	40	MAX
INSULATION RESISTANCE	500	M OHMS MIN	AT DC 100V
3. MECHANICAL PARAMETER
SOLDERABILITY	95% COVERAGE BY USING 90/10 SOLD AT 245 FOR 5 SEC.		DIPPING AFTER IMMERSION IN ALPHA 611 FLUX FOR 5 SEC.
MECHANICAL ENDURANCE - SHOCK	Electrical characteristics shall be satisfied after dropping three times from the height of 50 cm onto Hard wooden board.
MECHANICAL ENDURANCE - VIBRATION	Electrical characteristics shall be satisfied after supplying following Vibration.
VIBRATION FREQUENCY	1055	Hz
REPEATED PERIOD	12	min
FULL CYCLE	1.5	mm PP
DIRECTION	X.Y.Z
TIME	2	hours/each direction
STRENGTH OF TERMINALS/LEADWIRES - PULLING	Body of specimen shall be fixed, and 900g of tension weight shall be supplied gradually to axial direction of terminals/lead-wires for 30 sec. After above test, there is no observation of any visual damages on the specimen.
STRENGTH OF TERMINALS/LEADWIRES - BENDING	Body of specimen shall be fixed, and 90degree bending shall be given, being supplied 225gs tension weight. After that, terminals/lead-wires shall be straightened gradually. Then the same bending and straightening shall be supplied to the opposite direction in the same axial. After above test, there is no observation of any visual damages on the specimen.
SEALING TIGHTNESS	There is no observation of gas bubble after specimen put in hot water at +90+95 for 5 min.
SOLDERING DIP	Terminals/lead-wires of specimen shall be dipped into solder melted tank at +2305 for 3sec. Dipping depth shall be 2mm from the bottom of specimens body. Soldering portion shall be covered in over 90% of terminals/lead-wires dipped.		(After applying ROSIN flux)
SOLDER HEATING	Terminals/lead-wires of specimen shall be dipped into solder melted tank at +35010 for 3 sec. Electrical characteristics shall be satisfied after dipping depth shall be 2mm from edge of terminals/lead-wires.
II ENVIRONMENTAL ENDURANCE
HUMIDITY	Electrical characteristics shall be satisfied after letting it alone at 602 in humidity of 9095% for 250 hours.
STORAGE IN LOW TEMPERATURE	Electrical characteristics shall be satisfied after letting it alone at -302 for 250 hours.
STORAGE IN HIGH TEMPERATURE	Electrical characteristics shall be satisfied after letting it alone at +852 for 250 hours.
TEMPERATURE CYCLE	Electrical characteristics shall be satisfied after supplying the following temperature cycle (3 cycles). Temperature shift from low to high, high to low shall be done in 1/min.