Crystal Oscillator HC 49SJJ 24 MHz 8PF 20ppm Frequency Stability KYX KUS240000820 Electronic Component

Name: Crystal Oscillator HC 49SJJ 24 MHz 8PF 20ppm Frequency Stability KYX KUS240000820 Electronic Component
Brand: Beijing Silk Road Enterprise Management Services Co., Ltd.

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

:
: HC-49SJJ/24.000MHZ
: 8PF/20ppm
: KUS240000820

:
:
: 0755-89315823, 89315866
: 0755-89315223
: www.kaiyuexiang.com


1.1 HOLDER TYPE	49US AT CUT
1.2 MODE OF VIBRATION	FUND S&A
1.3 OSCILLATION MODE	KH-1240
1.4 TEST FACILITIES
1.5 STORAGE TEMPERATURE	-40TO +85
1.6 DRIVER LEVEL	100W
2.1 NORMAL FREQUENCY	24.000	MHz
2.2 FREQUENCY TOLERANCE252	20	ppm
2.3 TEMPERATURE STABILITY	20	ppm
2.4 OPERATING TEMPERATURE RANGE	-20TO +70
2.5 LOAD CAPACITANCE	8	PF
2.6 MOTIONAL CAPACITANE	3	PF MAX
2.7 SHUNT CAPACITANCE
2.8 EFFECTIVE SERIES RESISTANCE	40	MAX
2.9 INSULATION RESISTANCE	500M	OHMS MIN	AT DC 100V
3.1 SOLDERABILITY	95%COVERAGE BY USING 90/10 SOLD AT 245FOR 5 SEC. DIPING AFTER IMMERSION IN ALPHA 611 FLUX FOR 5 SEC.
MECHANICAL ENDURANCE - 1 SHOCK	Electrical characteristics shall be satisfied after dropping three time from the height of 50 cm onto Hard wooden board .
MECHANICAL ENDURANCE - 2 VIBRATION	Electrical characteristics shall be satisfied after supplying following Vibration .
(2) VIBRATION FREQUENCY	1055Hz
(3) REPEATED PERIOD	12min
(4) FULL CYCLE	1.5mm PP
(5) DIRECTION	X.Y.Z		2hours/each direction
MECHANICAL ENDURANCE - 3 STRENGTH OF TERMINALS/LEADWIRES -1 PULLING	a)Body of specimen shall be fixed, and 900g of tension weight shall be supplied gradually to axial direction of terminals/lead-wires for 30 sec . b)After above test a), there is no observation of any visual damages on the specimen.
MECHANICAL ENDURANCE - 3 STRENGTH OF TERMINALS/LEADWIRES -2 BENDING	a)Body of specimen shall be fixed, and 90degree bending shall be given, being supplied 225gs tension weight . After that, terminals/lead-wires shall be straightened gradually . Then the same bending and straightening shall be supplied to the opposite direction in the same axial . (Refer to Fig-1) b)After above test a), there is no observation of any visual damages on the specimen .
MECHANICAL ENDURANCE - 4 SEALING TIGHTNESS	There is no observation of gas bubble after specimen put in hot water at +90+95for 5 min .
MECHANICAL ENDURANCE - 5 SOLDERING DIP	Terminals/lead-wires of specimen shall be dipped into solder melted tank at +2305 for 3sec . Dipping depth shall be 2mm from the bottom of specimens body . (After applying ROSIN flux) Soldering portion shall be covered in over 90% of terminals/lead-wires dipped .
MECHANICAL ENDURANCE - 6 SOLDER HEATING	Terminals/lead-wires of specimen shall be dipped into solder melted tank at +35010 for 3 sec . Electrical characteristics shall be satisfied after dipping depth shall be 2mm from edge of terminals/lead-wires .
ENVIRONMENTAL ENDURANCE - 1 HUMIDITY	Electrical characteristics shall be satisfied after letting it alone at 602in humidity of 9095% for 250 hours .
ENVIRONMENTAL ENDURANCE - 2 STORAGE IN LOW TEMPERATURE	Electrical characteristics shall be satisfied after letting it alone at -302for 250 hours .
ENVIRONMENTAL ENDURANCE - 3 STORAGE IN HIGH TEMPERATURE	Electrical characteristics shall be satisfied after letting it alone at +852for 250 hours .
ENVIRONMENTAL ENDURANCE - 4 TEMPERATURE CYCLE	Electrical characteristics shall be satisfied after supplying the following temperature cycle (3cycles) . Temperature shift from low to high, high to low shall be done in 1/min (Refer to Fig-2) .