Crystal Oscillator 13.52127 MHz 20ppm Frequency Stability KYX KBD13521272020 Electronic Component

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

49USSMD/13.52127MHZ

KBD13521272020

20PF/20ppm

P.4

TEL0755-89315823 89315866 FAX0755-89315223

www.kaiyuexiang.com


1. GENERAL
1.1 HOLDER TYPE	49USSMD
1.2 MODE OF VIBRATION	AT CUT
1.3 OSCILLATION MODE	FUND S&A KH-1240
1.4 TEST FACILITIES
1.5 STORAGE TEMPERATURE	-40TO +85
1.6 DRIVER LEVEL	100W
2. ELECTRICAL PARAMETER
2.1 NORMAL FREQUENCY	13.52127 MHz
2.2 FREQUENCY TOLERANCE252	20ppm
2.3 TEMPERATURE STABILITY	20ppm
2.4 OPERATING TEMPERATURE RANGE	-20TO + 70
2.5 LOAD CAPACITANCE	20 PF
2.6 MOTIONAL CAPACITANCE	7PF MAX
2.7 SHUNT CAPACITANCE
2.8 EFFECTIVE SERIES RESISTANCE	40MAX
2.9 INSULATION RESISTANCE	500M OHMS MIN AT DC 100V
3. MECHANICAL PARAMETER
3.1 SOLDERABILITY	95%COVERAGE BY USING 90/10 SOLD AT 245FOR 5 SEC. DIPING AFTER IMMERSION IN ALPHA 611 FLUX FOR 5 SEC.
MECHANICAL ENDURANCE		Provided that measurement shall be carried out after letting it alone in the room temperature for 1 hour.
1 SHOCK	Electrical characteristics shall be satisfied after dropping three time from the height of 50 cm onto Hard wooden board.
2 VIBRATION	Electrical characteristics shall be satisfied after supplying following Vibration. (1)VIBRATION FREQUENCY: 1055Hz (2)REPEATED PERIOD: 12min (3)FULL CYCLE: 1.5mm PP (4)DIRECTION: X.Y.Z (5)TIME: 2hours/each direction
3 STRENGTH OF TERMINALS/LEADWIRES	-1 PULLING: a)Body of specimen shall be fixed, and 900g of tension weight shall be supplied gradually to axial direction of terminals/lead-wires for 30 sec. b)After above test a), there is no observation of any visual damages on the specimen. -2 BENDING: a)Body of specimen shall be fixed, and 90degree bending shall be given, being supplied 225gs tension weight. After that, terminals/lead-wires shall be straightened gradually. Then the same bending and straightening shall be supplied to the opposite direction in the same axial. b)After above test a), there is no observation of any visual damages on the specimen.
4 SEALING TIGHTNESS	There is no observation of gas bubble after specimen put in hot water at +90+95for 5 min.
5 SOLDERING DIP	Terminals/lead-wires of specimen shall be dipped into solder melted tank at +2305 for 3sec. Dipping depth shall be 2mm from the bottom of specimens body. (After applying ROSIN flux) Soldering portion shall be covered in over 90% of terminals/lead-wires dipped.
6 SOLDER HEATING	Terminals/lead-wires of specimen shall be dipped into solder melted tank at +35010 for 3 sec. Electrical characteristics shall be satisfied after dipping depth shall be 2mm from edge of terminals/lead-wires.
II ENVIRONMENTAL ENDURANCE		Provided that measurement shall be carried out after letting it alone in the room temperature for 1 hour.
1 HUMIDITY	Electrical characteristics shall be satisfied after letting it alone at 602in humidity of 9095% for 250 hours.
2 STORAGE IN LOW TEMPERATURE	Electrical characteristics shall be satisfied after letting it alone at -302for 250 hours.
3 STORAGE IN HIGH TEMPERATURE	Electrical characteristics shall be satisfied after letting it alone at +852for 250 hours.
4 TEMPERATURE CYCLE	Electrical characteristics shall be satisfied after supplying the following temperature cycle (3cycles). Temperature shift from low to high, high to low shall be done in 1/min.