aluminum electrolytic capacitor Man Yue Tech EGF158M1EG20CB with PET vinyl sleeve and rubber sealing

Product Overview

The SAMXON GF Series Aluminum Electrolytic Capacitors are polar, foil-type capacitors designed for use in electronic equipment. These capacitors meet IEC60384 standards and are constructed with a single-ended, wound element impregnated with electrolyte, enclosed in an aluminum case and sealed with end seal rubber, finished with a PET vinyl sleeve. They are suitable for applications requiring reliable performance and durability.

Product Attributes

• Brand: SAMXON
• Series: GF Series
• Construction Type: Single ended, foil type
• Sleeve Material: PET
• Lead Line Material: Tinned CP wire (Pb Free)
• Terminal Material: Aluminum wire
• Sealing Material: Rubber
• Case Material: Aluminum case
• Separator Material: Electrolyte paper
• Standard Compliance: IEC60384

Technical Specifications

Additional Technical Details

Standard Atmospheric Conditions for Measurement:
Ambient temperature: 15C to 35C
Relative humidity: 45% to 85%
Air Pressure: 86kPa to 106kPa

Specific Measurement Conditions:
Nominal Capacitance Measurement Frequency: 120Hz12Hz
Nominal Capacitance Measurement Voltage: Not more than 0.5Vrms
Nominal Capacitance Measurement Temperature: 202C

Terminal Strength:
Tensile Force (0.5mm and less wire): 5 N (0.51 kgf)
Bending Force (0.5mm and less wire): 2.5 N (0.25 kgf)
Tensile Force (Over 0.5mm to 0.8mm wire): 10 N (1.0 kgf)
Bending Force (Over 0.5mm to 0.8mm wire): 5 N (0.51 kgf)

Load Life Test:
Test Temperature: 105C 2
Duration: As per Table 1 (specific duration not detailed in this extract for this specific part number)
Criteria: Leakage current within specified value, Capacitance Change within 25%, tan not more than 150% of specified value, no electrolyte leakage.

Shelf Life Test:
Storage Temperature: 1052
Storage Time: 1000+48/0 hours
Criteria: Leakage current within specified value, Capacitance Change within 25%, tan not more than 150% of specified value, no electrolyte leakage.

Surge Test:
Cycles: 1000
Charge Time: 30 5s
Discharge Time: 5 min 30s
Test Temperature: 15~35
Criteria: Leakage current not more than specified value, Capacitance Change within 15%, tan not more than specified value, no electrolyte leakage.

Vibration Test:
Frequency Range: 10Hz ~ 55Hz
Amplitude: 1.5mm peak to peak
Duration: 2 hours in each of 3 mutually perpendicular directions
Criteria: No intermittent contacts, open or short circuiting, no damage to tab terminals or electrodes, no mechanical damage, no electrolyte leakage or swelling, legible markings.

Solderability Test:
Soldering Temperature: 2453
Dipping Depth: 2mm
Dipping Speed: 252.5mm/s
Dipping Time: 30.5s
Criteria: Minimum 95% of the surface immersed.

Resistance to Solder Heat Test:
Immersion Temperature: 2605 for 101 seconds OR 40010 for 3+0/-1 seconds
Dipping Depth: 1.5~2.0mm from the body
Criteria: Leakage current not more than specified value, Capacitance Change within 10%, tan not more than specified value, no electrolyte leakage.

Change of Temperature Test:
Temperature Cycles: 5 cycles (1: +20, 2: -40/-25 for 302 min, 3: +105 for 302 min)
Criteria: Leakage current not more than specified value, tan not more than specified value, no electrolyte leakage.

Damp Heat Test:
Conditions: 90~95% RH at 402 for 5008 hours
Criteria: Leakage current not more than specified value, Capacitance Change within 20%, tan not more than 120% of specified value, no electrolyte leakage.

Vent Test (for products with vent, diameter 6.3mm):
DC Current: 1A (for diameter 22.4mm or less)
Criteria: Vent operates with no dangerous conditions (flames, dispersion of pieces).

Maximum Permissible Ripple Current:
Specified at 100kHz and maximum operating temperature.