aluminum electrolytic capacitor Man Yue Tech ERT826M2HL30RRS9A1R with vinyl sleeve and aluminum case

Product Overview

The SAMXON RT Series Aluminum Electrolytic Capacitors are polar, foil-type capacitors designed for electronic equipment. They meet IEC60384 standards and feature a single-ended construction with an aluminum case, end seal rubber, and vinyl sleeve. These capacitors are suitable for applications requiring reliable performance and a wide operating temperature range.

Product Attributes

• Brand: SAMXON
• Series: RT Series
• Construction Type: Single ended, foil type
• Case Material: Aluminum
• Sleeve Material: PET
• Sealing Material: Rubber
• Lead Wire Material: Tinned CP wire (Pb Free)
• Terminal Material: Aluminum wire
• Separator Material: Electrolyte paper
• Standard Compliance: IEC60384

Technical Specifications

General Characteristics

• Standard Atmospheric Conditions: Ambient temperature: 15C to 35C, Relative humidity: 45% to 85%, Air Pressure: 86kPa to 106kPa. For precise measurements: Ambient temperature: 20C 2C, Relative humidity: 60% to 70%, Air Pressure: 86kPa to 106kPa.
• Operating Temperature Range: Refer to Table 1 for temperature range.
• Rated voltage (WV) & Surge voltage (SV): 160V(200V), 200V(250V), 220V(270V), 250V(300V), 350V(400V), 400V(450V), 420V(470V), 450V(500V), 500V(550V).
• Nominal Capacitance (Tolerance): Measured at 120Hz12Hz, not more than 0.5Vrms, at 202. Shall be within specified tolerance.
• Leakage Current: Measured after connecting with a protective resistor (1k10) in series for 2 minutes. Refer to Table 1 for criteria.
• tan: Measured at 120Hz12Hz, not more than 0.5Vrms, at 202. Refer to Table 1 for criteria.
• Terminal Strength: Tensile force: 5N (0.51kgf) for 0.5mm diameter, 10N (1.0kgf) for >0.5mm to 0.8mm diameter. Bending force: 2.5N (0.25kgf) for 0.5mm diameter, 5N (0.51kgf) for >0.5mm to 0.8mm diameter. No breakage or looseness.
• Temperature Characteristics: Tested at various temperatures (-40/-25, 20, 105). Criteria include limits for tan, leakage current, and impedance ratio at low temperatures.
• Load Life Test: Tested at 105C 2 with DC bias voltage plus rated ripple current for specified hours. Criteria include leakage current, capacitance change (within 20%), tan (not more than 200%), and appearance (no electrolyte leakage).
• Shelf Life Test: Stored at 1052 for 1000+48/0 hours. Criteria include leakage current, capacitance change (within 20%), tan (not more than 200%), and appearance (no electrolyte leakage).
• Surge Test: Applied surge voltage with a resistor. 1000 cycles of charge (305s) and discharge (5 min 30s) at 15~35. Criteria include leakage current, capacitance change (within 15%), tan, and appearance (no electrolyte leakage).
• Vibration Test: 10Hz ~ 55Hz, 1.5mm peak to peak amplitude, for 2 hours in 3 mutually perpendicular directions. Criteria include no intermittent contacts, open/short circuits, or damage.
• Solderability Test: Sn-Cu solder at 2503, dipping depth 2mm, dipping speed 252.5mm/s, dipping time 30.5s. Minimum 95% surface coated.
• Resistance to Solder Heat Test: Terminals immersed in solder bath at 2605 for 101 seconds or 40010 for 3+0/-1 seconds. Criteria include leakage current, capacitance change (within 10%), tan, and appearance (no electrolyte leakage).
• Change of Temperature Test: 5 cycles of temperature changes (-40/-25, +105, +20). Criteria include leakage current, tan, and appearance (no electrolyte leakage).
• Damp Heat Test: 5008 hours at 90~95% RH, 402. Criteria include leakage current, capacitance change (within 20%), tan (not more than 120%), and appearance (no electrolyte leakage).
• Vent Test: For products with vent (diameter 6.3). DC test with reversed polarity. Criteria: Vent operates with no dangerous conditions.
• Maximum Permissible (Ripple Current): Maximum AC current at 120Hz and maximum operating temperature. Frequency multipliers provided for different frequencies. Temperature coefficients provided for different temperatures.

Environment-related Substances

Refers to the latest document of Environment-related Substances standard (WI-HSPM-QA-072). Controlled substances include heavy metals, chlorinated organic compounds, brominated organic compounds, and specific phthalates, among others.

Attachment: Application Guidelines

Provides guidance on circuit design, capacitor handling, insertion, soldering, cleaning, and disposal to ensure optimal performance and safety.