Electrolytic Capacitors Man Yue Tech EGT225M1HD11RR With Aluminum Case And Tinned CP Wire Lead Lines
SAMXON GT Series Aluminum Electrolytic Capacitors
Product Overview
This specification applies to polar Aluminum electrolytic capacitors (foil type) designed for use in electronic equipment. Manufactured by MAN YUE ELECTRONICS COMPANY LIMITED under the SAMXON brand, the GT series capacitors meet IEC60384 standards. These capacitors are constructed with a single-ended type, featuring terminals fixed to anode and cathode foil, wound with paper, impregnated with electrolyte, enclosed in an aluminum case, and sealed with end seal rubber, finished with a vinyl sleeve. They are suitable for general electronic equipment applications.
Product Attributes
- Brand: SAMXON
- Manufacturer: MAN YUE ELECTRONICS COMPANY LIMITED
- Category: ALUMINUM ELECTROLYTIC CAPACITORS
- Series: GT Series
- Construction Type: Single Ended, Foil Type
- Sleeve Material: PET
- Lead Line Material: Tinned CP wire (Pb Free)
- Terminal Material: Aluminum wire
- Sealing Material: Rubber
- Case Material: Aluminum case
- Separator Material: Electrolyte paper
- Standards Compliance: IEC60384
- Environment-related Substances: Controlled substances list provided (see section 5 of original document for details).
Technical Specifications
| SAMXON Part No. | WV (Vdc) | Cap. (F) | Cap. tolerance | Temp. range() | tan (120Hz, 20) | Leakage Current (A, 2min) | Max Ripple Current at 105 100KHz (mA rms) | Impedance at 20 100kHz (max) | Load lifetime (Hrs) | Dimension (mm) DL | F (mm) | d (mm) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| EGT225M1HD11RR**P-R | 50 | 2.2 | -20%~+20% | -40~105 | 0.10 | 3 | 43 | 2.5 | 5000 | 5X11 | 2.0 | 0.5 |
Rated Voltage & Surge Voltage (Table 2)
| WV (V.DC) | SV (V.DC) |
|---|---|
| 6.3 | 8 |
| 10 | 13 |
| 16 | 20 |
| 25 | 32 |
| 35 | 44 |
| 50 | 63 |
| 63 | 79 |
| 100 | 125 |
Standard Atmospheric Conditions for Measurement:
- Ambient temperature: 15 to 35 (or 20 2 for precise measurements)
- Relative humidity: 45% to 85% (or 60% to 70% for precise measurements)
- Air Pressure: 86kPa to 106kPa
Dimension Notes:
- (L
- (D
- Dimensions: F0.5, L+ max, D+ max, d0.05
- Safety vent for 6.3
Application Guidelines:
- Circuit Design: Considerations for operating temperature, frequency, reverse voltage, charge/discharge applications, over-voltage, and ripple current.
- Series/Parallel Use: Guidelines for using multiple capacitors in series or parallel.
- Mounting Considerations: Advice on circuit board design, hole positioning, spacing, clearance for pressure relief vents, and wiring near vents.
- Electrical Isolation: Requirements for isolating capacitor terminals and cases.
- Capacitor Handling: Pre-use checks, insertion, manual and flow soldering, post-solder handling, circuit board cleaning, and use of adhesives/coatings.
- Precautions: Environmental conditions to avoid (temperature, water, humidity, gases, radiation, vibration) and electrical precautions (shock hazards, short circuits).
- Emergency Procedures: Actions to take if the pressure relief vent operates.
- Long Term Storage: Reconditioning requirements for capacitors stored for extended periods.
- Capacitor Disposal: Recommended disposal methods.
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.