Electrolytic capacitor Man Yue Tech EGF337M1JG20CB featuring aluminum case and PET sleeve protection
Price:
Negotiable
MOQ:
Negotiable
Delivery Time:
Negotiable
Product Description
SAMXON GF Series Aluminum Electrolytic Capacitors
Product Overview
The SAMXON GF Series Aluminum Electrolytic Capacitors are polar, foil-type capacitors designed for use in electronic equipment. Meeting IEC60384 standards, these capacitors are constructed with a single-ended type, featuring terminals fixed to anode and cathode foil, wound with paper, and impregnated with electrolyte. They are enclosed in an aluminum case, sealed tightly with end seal rubber, and finished with a vinyl sleeve. The GF series offers reliable performance across a wide operating temperature range and is suitable for general electronic applications.
Product Attributes
- Brand: SAMXON
- Category: ALUMINUM ELECTROLYTIC CAPACITORS
- Construction Type: Single ended, foil type
- Sleeve Material: PET
- Lead Line Material: Tinned CP wire (Pb Free)
- Terminal Material: Aluminum wire
- Sealing Material: Rubber
- Case Material: Aluminum case
- Separator Material: Electrolyte paper
Technical Specifications
| SAMXON Part No. | WV (Vdc) | Cap. (F) | Cap tolerance | Temp. range() | tan (120Hz, 20) | Leakage Current (A, 2min) | Max Ripple Current at 105 100kHz (mA rms) | Impedance at 20 100kHz (max) | Load lifetime (Hrs) | Dimension (mm) DL | Dimension (mm) F | Dimension (mm) d |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| EGF337M1JG20CB**P | 63 | 330 | -20%~+20% | -40~105 | 0.09 | 208 | 466 | 0.168 | 3000 | 10X20 | 5.0 | 0.6 |
Additional Technical Data
| ITEM | PERFORMANCE |
|---|---|
| 4.1 Rated voltage (WV) | WV (V.DC): 6.3, 10, 16, 25, 35, 50, 63, 100 SV (V.DC): 8, 13, 20, 32, 44, 63, 79, 125 |
| 4.2 Nominal capacitance (Tolerance) | Condition: Measuring Frequency: 120Hz12Hz, Measuring Voltage: Not more than 0.5Vrms, Measuring Temperature: 202 Criteria: Shall be within the specified capacitance tolerance. |
| 4.3 Leakage current | Condition: Connecting the capacitor with a protective resistor (1k 10 ) in series for 2 minutes, and then, measure Leakage Current. Criteria: Refer to Table 1 |
| 4.4 tan | Condition: See 4.2, Norm Capacitance, for measuring frequency, voltage and temperature. Criteria: Refer to Table 1 |
| 4.5 Terminal strength | Condition: Tensile Strength of Terminals, Bending Strength of Terminals. Criteria: No noticeable changes shall be found, no breakage or looseness at the terminal. |
| 4.6 Temperature characteristics | Condition: STEP Testing Temperature() Time 1 202 Time to reach thermal equilibrium 2 -40(-25) 3 Time to reach thermal equilibrium 3 202 Time to reach thermal equilibrium 4 1052 Time to reach thermal equilibrium 5 202 Time to reach thermal equilibrium Criteria: a. tan shall be within the limit of Item 4.4. Leakage current shall not more than 8 times of its specified value. b. In step 5, tan shall be within the limit of Item 4.4. Leakage current shall not more than the specified value. c. At-40 (-25), impedance (z) ratio shall not exceed the value of the table provided. |
| 4.7 Load life test | Condition: According to IEC60384-4No.4.13 methods, at 105C 2 with DC bias voltage plus the rated ripple current for Table 1. Criteria: Leakage current: Value in 4.3 satisfied. Capacitance Change: Within 25% of initial value. tan: Not more than 150% of the specified value. Appearance: No leakage of electrolyte. |
| 4.8 Shelf life test | Condition: Stored with no voltage applied at 1052 for 1000+48/0 hours. Stabilized at room temperature for 4~8 hours. Connected to a series limiting resistor(1k100 ) with D.C. rated voltage applied for 30min. Criteria: Leakage current: Value in 4.3 satisfied. Capacitance Change: Within 25% of initial value. tan: Not more than 150% of the specified value. Appearance: No leakage of electrolyte. |
| 4.9 Surge test | Condition: Applied a surge voltage with a (100 50)/CR (k) resistor. 1000 cycles, each consisting of charge of 30 5s, followed discharge of 5 min 30s. Test temperature: 15~35. Criteria: Leakage current: Not more than the specified value. Capacitance Change: Within 15% of initial value. tan: Not more than the specified value. Appearance: No leakage of electrolyte. |
| 4.10 Vibration test | Condition: 10Hz ~ 55Hz, Peak to peak amplitude: 1.5mm, for 2 hours in each of 3 mutually perpendicular directions. Criteria: No intermittent contacts, open or short circuiting. No damage of tab terminals or electrodes. No mechanical damage in terminal. No leakage of electrolyte or swelling of the case. Markings legible. |
| 4.11 Solderability test | Condition: Sn-Cu solder, Soldering temperature: 2503C, Dipping depth: 2mm, Dipping speed: 252.5mm/s, Dipping time: 30.5s. Criteria: Coating quality: A minimum of 95% of the surface being immersed. |
| 4.12 Resistance to solder heat test | Condition: Immersed into solder bath at 2605 for 10 1seconds or 40010 for 3 0 1 seconds to 1.5~2.0mm from the body. Criteria: Leakage current: Not more than the specified value. Capacitance Change: Within 10% of initial value. tan: Not more than the specified value. Appearance: No leakage of electrolyte. |
| 4.13 Change of temperature test | Condition: Temperature Cycle: According to IEC60384-4No.4.7methods, 5 cycles. Criteria: Leakage current: Not more than the specified value. tan: Not more than the specified value. Appearance: No leakage of electrolyte. |
| 4.14 Damp heat test | Condition: 5008 hours in an atmosphere of 90~95%R H .at 402. Criteria: Leakage current: Not more than the specified value. Capacitance Change: Within 20% of initial value. tan: Not more than 120% of the specified value. Appearance: No leakage of electrolyte. |
| 4.15 Vent test | Condition: For products with vent, diameter 6.3. DC test with reversed polarity. Applied DC Current from Table 3. Criteria: The vent shall operate with no dangerous conditions such as flames or dispersion of pieces. |
| 4.16 Maximum permissible (ripple current) | The maximum A.C current at 120Hz and can be applied at maximum operating temperature. Frequency Multipliers provided for different frequencies and capacitance values. |
Environment-related Substances Controlled
Refer to the latest document of Environment-related Substances standard(WI-HSPM-QA-072). Controlled substances include heavy metals (Cadmium, Lead, Mercury, Hexavalent chromium compounds), chlorinated organic compounds, brominated organic compounds, organotin compounds, asbestos, azo compounds, formaldehyde, beryllium compounds, specific phthalates, HFC, PFC, PFOS, and specific Benzotriazole.
Attachment: Application Guidelines
Provides detailed guidance on circuit design, capacitor handling, soldering, cleaning, and disposal to ensure optimal performance and safety.
Similar Products
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.
Company
Beijing Silk Road Enterprise Management Services Co., Ltd.
Location
16 Floor, Unit B, Jiatai International Mansion, No 41, Dongsihuan Zhong Road, Chaoyang District, Beijing
Contact Person
Sellina