SAMXON HP Series Aluminum Electrolytic Capacitors

Product Overview
The SAMXON HP Series Aluminum Electrolytic Capacitors are polar, foil-type capacitors designed for use in electronic equipment. These capacitors meet IEC60384 standards and are constructed with a single-ended design, featuring an aluminum case impregnated with electrolyte and sealed with end seal rubber, finished with a PET vinyl sleeve. They are suitable for various electronic applications requiring reliable capacitance and voltage ratings.

Product Attributes

• Brand: SAMXON
• Series: HP Series
• Type: Polar Aluminum Electrolytic Capacitor (foil type)
• Construction: Single ended, wound element, aluminum case, PET sleeve
• Materials: Aluminum case, PET sleeve, Solder coated copper clad steel terminals, Rubber-laminated bakelite seal, Aluminum rivet/washer/tab, Aluminum foil & Electrolyte paper element
• Standards: IEC60384

Technical Specifications

Key Characteristics & Tests

• Standard Atmospheric Conditions: Ambient temperature 15-35, Relative humidity 45-85%, Air Pressure 86-106kPa. For critical measurements: Ambient temperature 202, Relative humidity 60-70%, Air Pressure 86-106kPa.
• Operating Temperature Range: -25 to 105 (at rated voltage).
• Rated Voltage (WV) & Surge Voltage (SV): Various ratings available (e.g., 10V to 500V WV, 13V to 550V SV).
• Capacitance Tolerance: Specified tolerance (e.g., 20%). Measured at 120Hz12Hz, 0.5Vrms, 202.
• Leakage Current: Measured after 5 minutes with a 1k10 protective resistor. Refer to Table 1 for values.
• tan (Dissipation Factor): Measured at 120Hz12Hz, 0.5Vrms, 202. Refer to Table 1 for values.
• Terminal Strength: Withstands a static load of 25N (2.5kgf) in the axial direction for 30s.
• Temperature Characteristics: Tests at various temperatures (-40, 20, 105) to check tan and leakage current. Impedance ratio at low temperatures specified.
• Load Life Test: 2000 Hrs at 1052 with DC bias and rated ripple current. Criteria include leakage current, capacitance change (20%), tan (200% of specified), and no electrolyte leakage.
• Shelf Life Test: 1000+48/0 Hrs at 1052 without voltage. Criteria include leakage current, capacitance change (15%), tan (150% of specified), and no electrolyte leakage.
• Surge Test: 1000 cycles of charge (305s) and discharge (5min 30s) with a surge voltage. Criteria include leakage current, capacitance change (15%), tan (within specified value), and no electrolyte leakage.
• Vibration Test: 10Hz ~ 55Hz, 1.5mm peak-to-peak amplitude for 2 hours in 3 directions. No mechanical damage, leakage, or internal circuit issues.
• Solderability Test: Sn-Cu solder at 2503, 2mm depth, 252.5mm/s, 30.5s. Minimum 95% surface coating.
• Resistance to Solder Heat Test: Immersion in solder at 2605 for 101s or 40010 for 3+0/-1s. Criteria include leakage current, capacitance change (10%), tan (within specified value), and no electrolyte leakage.
• Change of Temperature Test: 5 cycles of temperature changes from +20 to rated low temperature (-40/-25) and rated high temperature (+105). Criteria for leakage current, tan, and appearance.
• Damp Heat Test: 5008 hours at 402, 90-95% RH. Criteria for leakage current, capacitance change (20%), tan (120% of specified), and no electrolyte leakage.
• Vent Test: For products with vents. DC reverse voltage test. Vent shall operate without dangerous conditions.
• Maximum Permissible Ripple Current: Maximum AC current at 120Hz and maximum operating temperature. Frequency and temperature multipliers provided.

Environment-related Substances

Refer to the latest document of Environment-related Substances standard (SX-WI-QA-343) for controlled substances.

Attachment: Application Guidelines

Provides detailed guidance on circuit design, capacitor handling, soldering, cleaning, mounting adhesives, precautions for use, emergency procedures, long-term storage, and disposal.