Aluminum Electrolytic Capacitor Man Yue Tech EGT475M1HD11HB with PET Sleeve and Tinned CP Wire Leads
Price:
Negotiable
MOQ:
Negotiable
Delivery Time:
Negotiable
Product Description
Product Overview
The SAMXON GT Series Aluminum Electrolytic Capacitors are foil-type, polar capacitors designed for use in electronic equipment. They meet IEC60384 standards and are constructed with a single-ended type, featuring tinned CP wire leads, aluminum foil electrodes, a rubber seal, aluminum case, and a PET sleeve. These capacitors are suitable for general electronic applications requiring reliable performance.
Product Attributes
- Brand: SAMXON
- Series: GT Series
- Construction: Single ended type, foil type, polar
- Sleeve Material: PET
- Lead Material: Tinned CP wire (Pb Free)
- Case Material: Aluminum case
- Origin: MAN YUE ELECTRONICS COMPANY LIMITED
Technical Specifications
| SAMXON Part No. | WV (Vdc) | Cap. (F) | Cap. tolerance | Temp. range () | tan (120Hz, 20) | Leakage Current (A, 2min) | Max Ripple Current at 105 100kHz (mA rms) | Impedance at 20 100kHz (max) | Load lifetime (Hrs) | Dimension (mm) DL | F | d | H1 |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| EGT475M1HD11HB**P | 50 | 4.7 | -20%~+20% | -40~105 | 0.10 | 3 | 88 | 1.900 | 5000 | 5X11 | 2.0~2.5 | 0.5 | 3.5 |
General Characteristics
| Item | Specification |
|---|---|
| Standard atmospheric conditions | Ambient temperature: 15C to 35C, Relative humidity: 45% to 85%, Air Pressure: 86kPa to 106kPa |
| Measurement conditions | Ambient temperature: 20C 2C, Relative humidity: 60% to 70%, Air Pressure: 86kPa to 106kPa |
| Rated voltage (WV) | 6.3, 10, 16, 25, 35, 50, 63, 100 V.DC |
| Surge voltage (SV) | 8, 13, 20, 32, 44, 63, 79, 125 V.DC |
| Nominal capacitance (Tolerance) measurement | Frequency: 120Hz12Hz, Voltage: Not more than 0.5Vrms, Temperature: 202 |
| Leakage current measurement | Series resistor: 1k10, Time: 2 minutes |
| tan measurement | Frequency: 120Hz12Hz, Voltage: Not more than 0.5Vrms, Temperature: 202 |
| Impedance measurement | Frequency: 100kHz, Temperature: 202, Measuring point: 2mm max from sealing rubber |
| Terminal strength (Tensile force) | 0.5mm and less: 5 N (0.51 kgf), Over 0.5mm to 0.8mm: 10 N (1.0 kgf) |
| Terminal strength (Bending force) | 0.5mm and less: 2.5 N (0.25 kgf), Over 0.5mm to 0.8mm: 5 N (0.51 kgf) |
| Load life test conditions | 105 2 C, DC bias voltage + rated ripple current, 5000+48/0 hours |
| Shelf life test conditions | 1052 for 1000+48/0 hours (no voltage applied) |
| Surge test cycles | 1000 cycles (Charge: 30 5s, Discharge: 5 min 30s) |
| Vibration test frequency range | 10Hz ~ 55Hz |
| Vibration test peak to peak amplitude | 1.5mm |
| Solderability test temperature | 2453C |
| Solderability test dipping time | 30.5s |
| Resistance to solder heat test temperature | 2605 for 101 seconds OR 40010 for 3 + 0 1 seconds |
| Change of temperature test cycles | 5 cycles (302 Minutes at -40/-25 and +105) |
| Damp heat test conditions | 90~95% RH at 402 for 500 8 hours |
| Vent test conditions (for products with vent) | DC test with reversed polarity, specific current applied based on diameter |
| Max permissible ripple current frequency multipliers | Refer to document for values at various frequencies and capacitance ranges. |
Application Guidelines Summary
- Capacitor parameters vary with temperature and frequency.
- Avoid reverse voltage, over voltage, and exceeding maximum ripple current.
- Use DC bipolar capacitors for circuits with changing or uncertain polarity.
- Standard capacitors are not suitable for repeating charge/discharge applications.
- Consider voltage imbalances when using capacitors in series and ripple current imbalances in parallel.
- Ensure proper mounting clearances for pressure relief vents.
- Avoid high voltage/current wiring near pressure relief vents.
- Capacitor sleeves are for identification and not electrical insulation.
- Handle capacitors carefully to avoid mechanical or electrical damage.
- Observe soldering temperature and time specifications.
- Avoid excessive stress on leads during insertion, soldering, and handling.
- Use appropriate cleaning solvents and drying methods.
- Avoid storing or using capacitors outside their rated environmental conditions.
- Emergency procedures for vent operation include immediate equipment shutdown.
- Recondition capacitors stored for long periods by applying rated voltage with a current limiting resistor.
- Dispose of capacitors by incineration after crushing or puncturing, or as solid waste, following local laws.
Environment-related Substances
Controlled substances list available, refer to the latest document "Environment-related Substances standard" (WI-HSPM-QA-072).
Similar Products
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.
Company
Beijing Silk Road Enterprise Management Services Co., Ltd.
Location
16 Floor, Unit B, Jiatai International Mansion, No 41, Dongsihuan Zhong Road, Chaoyang District, Beijing
Contact Person
Sellina