Aluminum case Man Yue Tech ERH187M2ML40RR electrolytic capacitor with foil type construction and sealing

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Overview

The SAMXON RH Series Aluminum Electrolytic Capacitors are polar, foil-type capacitors designed for use in electronic equipment. These capacitors meet IEC60384 standards and are constructed with an aluminum case, sealed with end seal rubber, and finished with a vinyl sleeve. They are suitable for general electronic applications requiring reliable performance.

Product Attributes

Brand: SAMXON
Series: RH Series
Construction Type: Single ended, foil type
Sleeve Material: PVC/PET
Lead Line Material: Tinned CP wire (Pb Free)
Terminal Material: Aluminum wire
Sealing Material: Rubber
Separator Material: Electrolyte paper
Case Material: Aluminum case
Standard Compliance: IEC60384

Technical Specifications

SAMXON Part No.	WV (Vdc)	Cap. (F)	Cap. tolerance	Temp. range ()	tan (120Hz, 20)	Leakage Current (A, 2min)	Max Ripple Current at 105 100kHz (mA rms)	Load lifetime (Hrs)	Dimension (mm) DL	F	d	Sleeve
ERH187M2ML40RR**F-R	420	180	-20%~+20%	-25~105	0.20	1537	2000	12000	18X40	7.5	0.8	PET

Additional Technical Data

Item	Description
Rated voltage (WV)	WV (V.DC): 160, 200, 250, 350, 400, 450, 500
Surge voltage (SV)	SV (V.DC): 200, 250, 300, 400, 450, 500, 550
Nominal capacitance measurement conditions	Frequency: 120Hz12Hz, Voltage: 0.5Vrms, Temperature: 202
Leakage current measurement conditions	Connected with a protective resistor (1k 10 ) in series for 2 minutes
tan measurement conditions	Refer to nominal capacitance measurement conditions
Terminal strength (Tensile force)	0.5mm and less: 5 N (0.51 kgf); Over 0.5mm to 0.8mm: 10 N (1.0 kgf)
Terminal strength (Bending force)	0.5mm and less: 2.5 N (0.25 kgf); Over 0.5mm to 0.8mm: 5 N (0.51 kgf)
Load life test conditions	105C 2, DC bias voltage + rated ripple current, tested after 16 hours recovery
Shelf life test conditions	1052 for 1000+48/0 hours, followed by 4~8 hours stabilization at room temperature, then DC rated voltage applied for 30min via 1k100 resistor
Surge test conditions	1000 cycles of 305s charge and 5 min 30s discharge, with a resistor (100 50)/CR (k), at 15~35
Vibration test conditions	10Hz ~ 55Hz, 1.5mm peak to peak amplitude, for 2 hours in each of 3 mutually perpendicular directions
Solderability test conditions	Soldering temperature: 2453, Dipping depth: 2mm, Dipping speed: 252.5mm/s, Dipping time: 30.5s
Resistance to solder heat test conditions	Solder bath at 2605 for 101s or 40010 for 3 0 1 s, 1.5~2.0mm from body
Change of temperature test conditions	5 cycles of: (1)+20 (3 min), (2)-25 (302 min), (3)+105 (302 min)
Damp heat test conditions	90~95% RH at 402 for 5008 hours
Vent test conditions (for 6.3)	DC test with reversed polarity, applied current from Table 2 (e.g., 1A for diameter 22.4mm)
Maximum permissible ripple current	Maximum AC current at 100kHz and maximum operating temperature. Combined DC and AC peak voltage must not exceed rated voltage.