SMD power inductor Microgate MPIT5040-3R3M-LF designed with Ni-Zn ferrite core and magnetic powder materials
Product Overview
The MPIT5040 series is a range of SMD power inductors designed for various electronic applications. These inductors offer reliable performance and are manufactured by SHENZHEN MICROGATE TECHNOLOGY CO., LTD.
Product Attributes
- Brand: MICROGATE
- Origin: Shenzhen, P.R.C.
- Material: Ni-Zn Ferrite core, Enameled Copper Wire, Ag/Ni/Sn/Cu terminals, Epoxy resin and magnetic powder for magnetic glue.
- Certifications: Lead-free products (LF)
Technical Specifications
| Microgate Part No. | Inductance (uH) | DCR () Max. | Isat (A) Max. | Irms (A) Max. | SRF (MHz) Min. |
|---|---|---|---|---|---|
| MPIT5040-1R0N-LF | 1.0 30% | 0.012 | 7.35 | 4.90 | 117 |
| MPIT5040-1R5N-LF | 1.530% | 0.015 | 6.30 | 4.30 | 86 |
| MPIT5040-2R2N-LF | 2.230% | 0.019 | 4.90 | 3.80 | 50 |
| MPIT5040-2R7N-LF | 2.730% | 0.022 | 4.30 | 3.60 | 37 |
| MPIT5040-3R3N-LF | 3.3 30% | 0.024 | 3.95 | 3.40 | 32 |
| MPIT5040-3R9N-LF | 3.9 30% | 0.027 | 3.55 | 3.20 | 29 |
| MPIT5040-4R7N-LF | 4.730% | 0.030 | 3.50 | 3.00 | 28 |
| MPIT5040-6R8M-LF | 6.820% | 0.043 | 2.90 | 2.50 | 21 |
| MPIT5040-100M-LF | 1020% | 0.064 | 2.35 | 2.10 | 18 |
| MPIT5040-150M-LF | 1520% | 0.086 | 2.00 | 2.00 | 13 |
| MPIT5040-220M-LF | 2220% | 0.129 | 1.60 | 1.50 | 11 |
| MPIT5040-330M-LF | 3320% | 0.188 | 1.30 | 1.20 | 9 |
| MPIT5040-470M-LF | 4720% | 0.272 | 1.10 | 1.00 | 7 |
| MPIT5040-680M-LF | 6820% | 0.400 | 0.90 | 0.80 | 6 |
| MPIT5040-101M-LF | 10020% | 0.560 | 0.75 | 0.70 | 5 |
Dimensions
| Dimensions | A | B | C | D | E | F | G | H |
|---|---|---|---|---|---|---|---|---|
| Values (mm) | 5.00.2 | 5.00.2 | 4.1Max. | 2.00.3 | 1.50.3 | 4.0Typ. | 1.5 Typ. | 3.6 Typ. |
Operating Conditions
Ambient Temperature: -40 ~ +125
Recommended Soldering Conditions
Flux: Rosin-based flux. Do not use highly acidic flux with halide content exceeding 0.2wt% (chlorine conversion value).
Solder: Use Sn solder.
Flow Soldering: Temperature difference between product surface and solder during pre-heating should not exceed 150. Temperature difference during cooling should not exceed 100.
Reflow Soldering Profile:
- Average Ramp-Up Rate: 3/second max.
- Preheat (Ts min. to Ts max.): 150 to 200, 60-180 seconds.
- Time maintained above 217 (tL): 60-150 seconds.
- Peak/Classification Temperature (Tp): 260, 3-4 seconds.
- Time within 5 C of actual Peak Temperature: 20-40 seconds.
- Ramp-Down Rate: 6C/second max.
- Time from 25 C to Peak Temperature: 8 minutes max.
Note: All temperatures are measured on the product surface.
Storage Conditions
Refer to Section 11 of the original document for detailed storage information.
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.