conductive polymer aluminium electrolytic capacitor Nantong Jianghai Capacitor PCV0JVM471MF08FVTSWP for electronic
Price:
Negotiable
MOQ:
Negotiable
Delivery Time:
Negotiable
Product Description
Product Overview
The HVM Series conductive polymer solid aluminum electrolytic capacitors are designed for high-performance applications. They offer reliability and stability across a wide temperature range, making them suitable for demanding electronic circuits.
Product Attributes
- Brand: Nantong Jianghai Capacitor Co., Ltd.
- Origin: China
- Product Type: Aluminium electrolytic capacitors with conductive polymer solid electrolyte
- Series: HVM Series
- Customer P/N: JH-HVM0J471M-1
Technical Specifications
| Item | Specifications | Test Method |
| Rated voltage | 6.3 V | |
| Rated capacitance | 470 F | 20,120Hz |
| Case size | 6.3 8 | |
| Tolerance on rated capacitance | 20 % | |
| Surge voltage | 7.2 V | |
| Leakage current | 592.2 A (max.) | 20, After 2 minutes |
| Tangent of loss angle (tan) | 12 % (max.) | 20,120Hz |
| Equivalent Series Resistance (ESR) | 14 m (max.) | 100 kHz |
| Rated ripple current | 3470 mA | 105 , 100kHz |
| Category temperature range | -55 to 105 | |
| Lifespan* | 105 , 2000 h | *The failure rate of capacitors follows JIS C 5003 standard, with a reliability level of 60 %, as follows: 0.5 % / 1,000 hours (Maximum operating temperature, load rated voltage ) |
| Frequency coefficient for ripple current | See table | |
| Leakage current | See specifications list | Series resistor: 1,000 Applied rated voltage 2 minutes. If this value is doubtful, performed the voltage treatment. Voltage treatment: The capacitor should be serially attached to a protective 1,000 resistor and d.c. voltage equivalent to the rated voltage should be applied for 2h at 105 2.Next, after letting the capacitor cool to room temperature, it should be discharged through a resistor of approximately 1 /V and then stored at standard atmospheric conditions for 12 h to 24 h. |
| Capacitance | See specifications list | Measuring circuit: Equivalent series circuit Frequency: 120 Hz10% Measuring voltage: 0.5 Vrms |
| Tangent of loss angle (tan) | See specifications list | Measuring temperature: 202 |
| Equivalent Series Resistance (ESR) | See specifications list | Frequency: 100 kHz10% Measuring voltage: 0.5Vrms, Measuring temperature: 202 |
| Solderability | At least 95% of circumferential surface of the dipped portion of termination shall be covered with new solder. | Solder bath method Flux: Rosin // Ethanol, About 25 wt% Sn-Ag-Cu solder Temperature: 2453, Duration: 30.3 seconds |
| Resistance to soldering heat change | Capacitance: Within 10% of the initial value; Tan: Within 1.3 times of the value of item 2; Leakage current: Within the value of item 2. | A) Solder bath method Temperature: 2605C, Duration: 5 1 seconds B) Soldering iron method Temperature: 40010C, Duration: 3+1/0 seconds Heat protector: t=1.6 mm glass-epoxy board. |
| Appearance | No visible damage, Legible marking | |
| Rapid change of temperature | Capacitance: Within 10% of the initial value; Tan: Within the value of item 2; Leakage current: Within the value of item 2. | TA=-55 TB= 105 Cycle number: 5 cycles Applied voltage: Without load |
| Shelf Life | Capacitance: Within 20% of the initial value; Tan: Within 2 times of the value of item 2; Leakage current: Within the value of item 2. | Temperature: 105 2, Time: 1000+36 hours Condition: The DC rated voltage shall be applied across the capacitor and its protective resistor (1K) for 30 minutes. The capacitor shall then be stored under standard atmospheric conditions for 24 ~ 48 hours. |
| Endurance | Capacitance: Within 20% of the initial value; Tan: Within 1.5 times of the value of item 2; ESR: Within 1.5 times of the value of item 2; Leakage current: Within the value of item 2. | Temperature: 105 2, Duration: 2000 +48/-0h Applied voltage: Rated voltage |
| Damp heat, steady state | Capacitance: Within 20% of the initial value; Tan: Within 1.5 times of the value of item 2; ESR: Within 1.5 times of the value of item 2; Leakage current: Within the value of item 2. (After voltage treatment) | Temperature: 602, Relative humidity: 90 to 95%, Duration: 1,000 +24/-0hours |
| Surge | Capacitance: Within 20% of the initial value; Tan: Within 1.5 times of the value of item 2; ESR: Within 1.5 times of the value of item 2; Leakage current: Within the value of item 2. | Temperature: Normal temperature, Applied voltage: 7.2 V, Protective resistor: 1 k, Cycle number: 1,000 cycles (A) Charge: 305 seconds (B) Discharge: 5.5 minutes (A) + (B): 1 cycle |
| Characteristics at high and low temperature | Capacitance: Within the initial specified value; Tangent of loss angle: Within the initial specified value; Impedance(Z) at 100KHz: Within the initial specified value. | Step 1: +202 |
| Characteristics at high and low temperature | Impedance(Z) at 100KHz: Z(-55)/Z(+20)1.25 | Step 2: -553, Place for two hours |
| Characteristics at high and low temperature | Impedance(Z) at 100KHz: Z(+105)/Z(+20)1.25 | Step 4: +1052, Place for two hours |
| Characteristics at high and low temperature | Capacitance change: Within 5% of Step 1; Tangent of loss angle: Within the initial specified value. | Step 5: +202 |
Similar Products
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.
Company
Beijing Silk Road Enterprise Management Services Co., Ltd.
Location
16 Floor, Unit B, Jiatai International Mansion, No 41, Dongsihuan Zhong Road, Chaoyang District, Beijing
Contact Person
Sellina