conductive polymer solid aluminum electrolytic capacitor Nantong Jianghai Capacitor PCR1AEL471MF08LL25WP for electronics

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

Product Overview

The HEL Series by Nantong Jianghai Capacitor Co., Ltd. features conductive polymer solid aluminum electrolytic capacitors. Designed for reliability and performance, these capacitors are suitable for a wide range of electronic applications.

Product Attributes

Brand: Nantong Jianghai Capacitor Co., Ltd.
Product Type: Aluminium electrolytic capacitors with conductive polymer solid electrolyte
Series: HEL Series
Origin: China
Color (Marking): Red (default, adjustable per customer request)

Technical Specifications

Item	Specification	Test Method
Rated voltage	2.5~16 V
Rated capacitance	100~1200 F (20,120Hz)
Tolerance on rated capacitance	20 %
Surge voltage	UR 1.15
Leakage current	See specifications list (20, After 2 minutes)	Series resistor: 1,000 Applied rated voltage 2 minutes. If this value is doubtful, performed the voltage treatment. Voltage treatment: The capacitor should be serially attached to a protective 1,000 resistor and d.c. voltage equivalent to the rated voltage should be applied for 2h at 105 2. Next, after letting the capacitor cool to room temperature, it should be discharged through a resistor of approximately 1 /V and then stored at standard atmospheric conditions for 12 h to 24 h.
Tangent of loss angle (tan)	See specifications list (20,120Hz)	Measuring temperature: 202
Equivalent Series Resistance (ESR)	See specifications list (100 kHz)	Frequency: 100 kHz10% Measuring voltage: 0.5Vrms, Measuring temperature: 202
Rated ripple current	See specifications list (105, 100 kHz)
Category temperature range	-55 to 105
Lifespan	105 , 2000 h
Solderability	At least 95% of circumferential surface of the dipped portion of termination shall be covered with new solder. Flux: Rosin // Ethanol, About 25 wt% Sn-Ag-Cu solder. Temperature: 2453, Duration: 20.3 seconds	Solder bath method
Robustness of terminations (Tensile)	See table	With the body of a capacitor fixed, the load shall be applied to the lead wire termination in its draw out direction, gradually up to the specified value.
Robustness of terminations (Bending)	See table	Suspend a weight corresponding to bending strength, bend the body through 90and return it to the original position. Carry out these operations during 2 to 3 seconds and count it as one cycle. Carry out similar operations in the opposite direction and count it as two cycles.
Resistance to soldering heat (Capacitance change)	Within 5% of the initial value	A) Solder bath method Temperature: 2605C, Duration: 10 1 seconds B) Soldering iron method Temperature: 40010C Duration: 3+1/0 seconds Heat protector: t=1.6 mm glass-epoxy board.
Resistance to soldering heat (tan)	Within the value of item 2.
Resistance to soldering heat (Leakage current)	Within the value of item 2.
Vibration (Capacitance)	Shall not show drastic change compared to the initial capacitance when measured within 30 minutes.	Frequency: 10 to 55 Hz (1 minute interval / 10 55 10 Hz) Amplitude: 0.75 mm (Total excursion 1.5 mm) Direction: X, Y, Z (3 axes) Duration: 2 hours / axial (Total 6 hour)
Vibration (Capacitance change)	Within 5% of the initial value
Vibration (tan)	Within the value of item 2.
Vibration (Leakage current)	Within the value of item 2.
Rapid change of temperature (Capacitance change)	Within 10% of the initial value	Applied voltage: Without load Cycle number: 5 cycles
Rapid change of temperature (tan)	Within the value of item 2.
Rapid change of temperature (Leakage current)	Within the value of item 2.