High Power Metal Current Sensing Resistors RVR HIRC12AR005F Featuring Low TCR and Lead Free Plating
Product Overview
This document details the Approval Specification for Metal Current Sensing Chip Resistors, Type 2512/1206/0805 series. These resistors offer high power capabilities up to 3W, with low TCR down to 50ppm/. They are suitable for reflow and wave soldering, feature halogen-free epoxy, lead-free plating, superior mechanical strength, and excellent high-frequency characteristics. They comply with RoHS standards.
Product Attributes
- Brand: (Changzhou Pengke Electronics)
- Origin: China
- Material: Metal Alloy
- Certifications: RoHS compliant, Halogen Free
Technical Specifications
| Product Category | Rated Power | Resistance Range | TCR | Operating Temperature Range | Resistance Tolerance | Insulation Resistance | Maximum Operating Voltage (V) |
| 2512 DD/XD | 2W/3W | 0mR 1m | 350ppm/ | -55 ~ +170 | F:1% G:2% J:5% | Over 100M | (P*R) |
| 1m<R 2m | 100ppm/ | ||||||
| 2m<R 500m | 50 ppm/ | ||||||
| 1206 RC | 1W | 0mR 2m | 350ppm/ | -55 ~ +170 | F:1% G:2% J:5% | Over 100M | (P*R) |
| 2m<R 200m | 50 ppm/ | ||||||
| 0805 RE | 0.5W | 5mR 15m | 50ppm/ | -55 ~ +170 | F:1% G:2% J:5% | Over 100M | (P*R) |
Construction and Dimension
| Category | L (mm) | W (mm) | T (mm) | A (mm) |
| 2512 | 6.40.20 | 3.20.20 | 0.80.20 | DD:2.00.20 (R4 m) XD:1.00.20 (R0.5 m) |
| 1206 | 3.20.20 | 1.60.20 | 0.70.20 | 0m R<10m 0.60.20 10m<R 200m 0.450.20 |
| 0805 | 2.00.10 | 1.250.10 | 0.50.20 | 0.350.20 |
Land Pattern Dimensions
| Category | a (mm) | b (mm) | L (mm) |
| 0805 RE | 1.5 | 1 | 1 |
| 1206 RC | 1.8 | 1.7 | 1.6 |
| 2512 XD | 4 | 2.1 | 4.1 |
| 2512 DD | 4 | 3.1 | 1.3 |
Reliability Tests
| Project | Test Method | Specifications and Requirements |
| Temperature coefficient (TCR) | Measured at 25(T1, R1) and 125(T2, R2) | Refer to TCR specifications for physical features |
| Short Time Overload | 5 times rated power, maintain 5s | R 1%+0.05m |
| Insulation resistance | Apply 100V15V DC voltage between electrode and substrate, hold for 60 seconds, then measure insulation resistance | > 100 M |
| Withstand voltage | An alternating current with an effective value of the maximum overload voltage is applied between the electrode and the substrate at a rate of approximately 100V/S, maintaining 605s | No breakdown or arc |
| Solderability | 2455 tin tank, hold 2s0.5s | At least 95% of surface area of electrode shall be covered with new solder |
| Resistance to Soldering Heat | 2605 tin tank, hold for 10s1s | R (0.5%+0.05m ), no visible damage |
| Bending test | Bending distance 2mm, hold time 60s5s | R0.5%+0.05m , no mechanical damage |
| Solvent resistance | Isopropanol (IPA) at 235 for 10 hours | No obvious damage to appearance |
| High Temperature Exposure | 1702, 1000H, stand for 1H, test the resistance value | R (1.0%+0.05m ) |
| Low Temperature Exposure | -552, 1000H, stand for 1H, test the resistance value | R (0.5%+0.05m ) |
| Rapid change of Temperature | -55 30 minutes ~ normal temperature 5 minutes ~155 30 minutes, 1000 cycles | R (0.5%+0.05m ) |
| Load Life | 702, 1000 hours, rated power, 1.5 hours on / 0.5 hours off | R (1.0%+0.05m ) |
| Moisture with Load | 852, 85%3%RH, 1000 hours, rated power, 1.5 hours on / 0.5 hours off | R (1.0%+0.05m) |
Tape Packaging Dimensions
| Type | A (mm) | B (mm) | C (mm) | D (mm) | E (mm) | T1 (mm) | T2 (mm) |
| 0805 | 1782.0 | 601.0 | 131.0 | 2.00.5 | >22 | 9.01 | / |
| 1206 | 1782.0 | 601.0 | 131.0 | 2.00.5 | >22 | 9.00.3 | 11.4 1.0 |
| 2512 | 1782.0 | 601.0 | 131.0 | 2.00.5 | >22 | 13.0 0.3 | 15.4 1.0 |
Reel Dimensions
| Type | D (mm) | C (mm) | E (mm) | T1 (mm) |
| 0805 | 178 | 60 | 13 | 9.0 |
| 1206 | 178 | 60 | 13 | 9.0 |
| 2512 | 178 | 60 | 13 | 13.0 |
Label
Quantity: 0805/1206: 5000pcs/Reel, 2512: 4000pcs/Reel. Label shall mark: Size, Quantity, LOT.NO., Manufacturers name.
Recommended Reflow Soldering Profile
Solder: Sn96.5 / Ag3 / Cu0.5. Peak Temperature: 240~260, 10 sec. Pre-heating Zone: 150 to 200 , 9030 sec. Soldering Zone: 230 or higher, 3010 sec.
Care Note
Storage: Temperature 535, Humidity 4575% RH. Avoid direct sunlight, moisture, dust, and harmful gases. Storage life: 1 year. Handling: Avoid exceeding rated power. Be careful when picking up with tweezers. Do not touch the product with the soldering tip during manual installation.
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.