Metal Chip Resistor RVR HIXD25NR006F with Wide Resistance Tolerance and High Operating Voltage Range
Product Overview
This document specifies the approval for metal current sensing chip resistors, specifically the 2512, 1206, and 0805 series. These resistors offer high power capabilities up to 3W, low TCR as 50ppm/, and are suitable for reflow and wave soldering. They feature halogen-free epoxy, lead-free plating, superior mechanical strength, and excellent high-frequency characteristics, complying with RoHS standards.
Product Attributes
- Brand: (Changzhou Pengke Electronics)
- Origin: China
- Material: Metal Alloy
- Certifications: RoHS compliant, Halogen Free
Technical Specifications
| Product Category | Rated Power | Resistance Range | TCR | Operating Temperature Range | Resistance Tolerance | Insulation Resistance | Max. Operating Voltage |
| 2512 DD/XD | 2W/3W | 0mR 1m | 350ppm/ | -55 ~ +170 | F:1% G:2% J:5% | Over 100M | (P*R) |
| 1m<R 2m | 100ppm/ | ||||||
| 2m<R 500m | 50 ppm/ | ||||||
| 1206 RC | 1W | 0mR 2m | 350ppm/ | -55 ~ +170 | F:1% G:2% J:5% | Over 100M | (P*R) |
| 2m<R 200m | 50 ppm/ | ||||||
| 0805 RE | 0.5W | 5mR 15m | 50ppm/ | -55 ~ +170 | F:1% G:2% J:5% | Over 100M | (P*R) |
Construction and Dimension
| Category | L (mm) | W (mm) | T (mm) | A (mm) |
| 2512 | 6.40.20 | 3.20.20 | 0.80.20 | DD:2.00.20 (R4 m) XD:1.00.20 (R0.5 m) |
| 1206 | 3.20.20 | 1.60.20 | 0.70.20 | 0m R<10m: 0.60.20; 10m<R 200m: 0.450.20 |
| 0805 | 2.00.10 | 1.250.10 | 0.50.20 | 0.350.20 |
Land Pattern Dimensions
| Category | a (mm) | b (mm) | L (mm) |
| 0805 RE | 1.5 | 1 | 1 |
| 1206 RC | 1.8 | 1.7 | 1.6 |
| 2512 XD | 4 | 2.1 | 4.1 |
| 2512 DD | 4 | 3.1 | 1.3 |
Reliability Tests
| Project | Test Method | Specifications and Requirements |
| Temperature coefficient (TCR) | Measured at 25(T1, R1) and 125(T2, R2), TCR=(R2-R1)/(R1(T2-T1))*10^6 | Refer to TCR specifications |
| Short Time Overload | 5 times rated power, maintain 5s | R 1%+0.05m |
| Insulation resistance | Apply 100V15V DC between electrode and substrate for 60s | > 100 M |
| Withstand voltage | Apply AC voltage of maximum overload voltage between electrode and substrate at approx. 100V/S, hold for 605s | No breakdown or arc |
| Solderability | 2455 tin bath, hold 2s0.5s | At least 95% of electrode surface area covered with new solder |
| Resistance to Soldering Heat | 2605 tin bath, hold for 10s1s | R (0.5%+0.05m ), no visible damage |
| Bending test | Bending distance 2mm, hold time 60s5s | R0.5%+0.05m , no mechanical damage |
| Solvent resistance | Isopropanol (IPA) at 235 for 10 hours | No obvious damage to appearance |
| High Temperature Exposure | 1702, 1000H | R (1.0%+0.05m ) |
| Low Temperature Exposure | -552, 1000H | R (0.5%+0.05m ) |
| Rapid change of Temperature | -55 30 min ~ normal temp 5 min ~155 30 min, 1000 cycles | R (0.5%+0.05m ) |
| Load Life | 702, 1000 hours, rated power, 1.5 hours on / 0.5 hours off | R (1.0%+0.05m ) |
| Moisture with Load | 852, 85%3%RH, 1000 hours, rated power, 1.5 hours on / 0.5 hours off | R (1.0%+0.05m) |
Tape Packaging Dimensions
| Type | A (mm) | B (mm) | C (mm) | D (mm) | E (>mm) | T1 (mm) | T2 (mm) |
| 0805 | 1782.0 | 601.0 | 131.0 | 2.00.5 | >22 | 9.01 | / |
| 1206 | 1782.0 | 601.0 | 131.0 | 2.00.5 | >22 | 9.00.3 | 11.4 1.0 |
| 2512 | 1782.0 | 601.0 | 131.0 | 2.00.5 | >22 | 13.0 0.3 | 15.4 1.0 |
Reel Dimensions
| Type | D (mm) | C (mm) | E (mm) | T1 (mm) |
| 0805 | 1782.0 | 601.0 | 131.0 | 9.01 |
| 1206 | 1782.0 | 601.0 | 131.0 | 9.00.3 |
| 2512 | 1782.0 | 601.0 | 131.0 | 13.0 0.3 |
Label
Packaging Quantity: 0805/1206: 5000pcs/Reel, 2512: 4000pcs/Reel
Label Markings: (1) Size (2) Quantity (3) LOT.NO. (4) Manufacturers name
Recommended Reflow Soldering Profile
1. Solder: Sn96.5 / Ag3 / Cu0.5
2. Peak Temperature: 240~260, 10 sec
3. Pre-heating Zone: 150 to 200 , 9030 sec
4. Soldering Zone: 230 or higher, 3010 sec
Care Note
1. Storage: Store in a controlled environment (temperature 535, relative humidity 4575% RH). Avoid direct sunlight, moisture, dust, and harmful gases. Storage life: 1 year.
2. Handling: Avoid exceeding rated power. Handle with care to prevent damage. Do not touch the product with a soldering tip during manual installation.
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.