Thin layer monolithic multilayer ceramic capacitor SAMWHA CS1608X7R222K500NRB for computer and LED equipment

Price Negotiable

Price: Negotiable

MOQ: Negotiable

Delivery Time: Negotiable

Product Description

SAMWHA CAPACITOR CO., LTD.

This document outlines the specifications for the MONOLITHIC MULTILAYER CERAMIC CAPACITOR (Thin Layer Large-Capacitance Type), part number CS1608X7R105K250NRB. These capacitors are designed for use in computer equipment, communication equipment, industrial equipment, and high reliability equipment such as LED applications.

Product Attributes

Brand: SAMWHA CAPACITOR CO., LTD.
Origin: KOREA
Date: 2017. 12. 22.
Standard: SW - M - 04B

Technical Specifications

SAMWHA Part No.	Type	Capacitance	Capacitance Tolerance	Dissipation Factor	Insulation Resistance	Chip Size (L x W x T)	Test Frequency	Test Voltage
CS1608X7R105K250NRB	Thin Layer Large-Capacitance	1	10 %	Max. 12.5 %	More than 50	1.60 0.15 x 0.80 0.10 x 0.80 0.10	1 0.1kHz	1 0.2Vrms

General Code Breakdown

Type Designation: CS1608X7R105K250NRB

1) Type: Monolithic Multilayer Ceramic Capacitor Leadless Type
2) Size Code: 1608 (Length: 1.6mm, Width: 0.8mm)
3) Temperature Coefficient Code: X7R (-55 to +125, 15%)
4) Capacitance Code: 105 (10 x 10^5 pF = 1 )
5) Capacitance Tolerance Code: K (10 %)
6) Voltage Code: 250 (250V DC)
7) Termination Code: N (Ni-Sn Plating)
8) Packing Code: R (7" Reel Type)
9) Thickness option: Not specified in this section, refer to page 2/8 for details.

Dimensions

Code	Dimension (L x W x T)	Tol()
1608	1.60 x 0.80 x 0.80	0.15 / 0.10 / 0.10

Specifications and Test Methods

No.	Item	Specification	Test Methods and Conditions
1	Operating Temperature Range	X7R : -55 to +125
2	Insulation Resistance	50 G min	Applied the rated voltage for 2 minutes of charging. The charge/discharge current is less than 50mA.
3	Dielectric Strength	No defects or abnormalities	X7R : The rated voltage 250% - Applied between the terminations for 1 to 5 seconds. - The charge/discharge current is less than 50mA.
4	Capacitance	within the specified tolerance	The capacitance/D.F. should be measured at 25 at the frequency and voltage shown in the table. Capacitance: C 10, Frequency: 1 0.1kHz, Voltage: 0.5~1.0Vrms Capacitance: C > 10, Frequency: 120 24Hz, Voltage: 0.50.1Vrms Initial measurement Perform the initial measurement according to Note1 for Class Measurement after test Take it out and set it for 242 hours (Class ) then measure.
5	Dissipation Factor	X7R : 12.5%max
6	Solderability of Termination	-Termination should be covered with more than 75% of new solder	Pb-Free type Solder : 96.5Sn-3Ag-0.5Cu Solder temperature : 2455 Immersion time : 30.1sec Pre-Heating : at 80~120 for 10~30sec
7	Resistance to Soldering Heat	Appearance No marking defects	Preheat the capacitor at 120 to 150 for 1 minute. Immerse the capacitor in a eutectic solder solution at 2605 for 100.5 seconds. Initial measurement Perform the initial measurement according to Note1 for Class Measurement after test Let sit at room temperature for 242 hours,then measure. Capacitance change