RUILON RL0603N503F4150FTF
Product Overview
Dissipation Factor: The required power which makes the NTC thermistor body temperature raise 1C through self-heated, normally expressed in milliwatts per degree Celsius (mW/C). It can be calculated by the following formula: 5 = X / (T - To), where X is the necessary electric power and (T-To) is the temperature rise.
Rated Power: The necessary electric power that makes the thermistor's temperature rise 100C by self-heating at an ambient temperature of 25C.
Permissible operating current: The current that keeps the body temperature of a chip NTC on the PC board in still air rising 1C by self-heating.
Notes on Rated Power: When Rated Electric Power (100mW) is applied to an NTC thermistor at 25C in still air, the temperature rise of the NTC thermistor is about 100C. However, too rapid temperature rise may cause unexpected failures. Do not apply more than 10mW of electric power in a short time (10mW of power will increase the temperature by about 10C). A current less than 1/10 of the Permissible Operating Current value is recommended to prevent self-heating.
| Item | Standard Test Methods and Remarks | Requirements |
|---|---|---|
| Terminal Strength | IEC 60068-2-21 Solder the chip to the testing jig (glass epoxy board) using eutectic solder. Then apply a force in the direction of the arrow. | No removal or split of the termination or other defects shall occur. |
| IEC 60068-2-21 R~ Size F {45 0F ) Duration | 0201: 5N 10+1s 0402, 0603: 5N 10+1s 0805: 10N | |
| Resistance to Flexure | IEC 60068-2-21 Solder the chip to the test jig (glass epoxy board) using a eutectic solder. Then apply a force in the direction shown as follow. | No visible damage. |
| Pressurizing Speed 0201, 1mm 0402, 0603, 0805 2mm | ||
| Vibration | IEC 60068-2-80 Solder the chip to the testing jig (glass epoxy board) using eutectic solder. The chip shall be subjected to a simple harmonic motion having a total amplitude of 1.5mm, the frequency being varied uniformly between the approximate limits of 10 and 55 Hz. | No visible damage. AR25/R25 2% |
| Frequency range: 10Hz55Hz10Hz 53R, BHIHN 1 48, E50 The frequency ranges from 10 to 55 Hz and return to 10 Hz shall be traversed in approximately 1 minute. This motion shall be applied for a period of 2 hours in each 3 mutually perpendicular directions (total of 6 hours). | ||
| Dropping | IEC 60068-2-32 Drop a chip 10 times on a concrete floor from a height of 1 meter. | No visible damage. |
| Solderability | IEC 60068-2-58 Solder temperature: 2455C. Duration: 30.3s. Solder: 96.5wt%Sn/3.0wt%Ag/0.5wt%Cu Flux: 25% Rosin and 75% ethanol in weight. | Wetting coverage shall exceed 95%. |
| Resistance to Soldering Heat | IEC 60068-2-58 Solder temperature: 2605C. Duration: 101s. Solder: 96.5wt%Sn/3.0wt%Ag/0.5wt%Cu Flux: 25% Rosin and 75% ethanol in weight. | No visible damage. AR25/R25 R/R |
| Recommended Soldering Technologies | Profile | Solder | Flux | Notes |
|---|---|---|---|---|
| Re-flowing Profile | Ramp: 1~2C/sec. Pre-heating: 150~170C/90+30 sec. Time above 240C: 20~40 sec. Peak temperature: 260C Max./10 sec. | 96.5wt%Sn/3.0wt%Ag/0.5wt%Cu | Rosin type flux | Max.2 times for re-flowing. Total accumulated soldering time at peak temperature within 30sec. Cooling: Gradual cooling in air. |
| Iron Soldering Profile | Iron soldering power: Max.20W Pre-heating: 150C/60sec. Soldering Tip temperature: 280 C Max. Soldering time: 3 sec Max. | 96.5wt%Sn/3.0wt%Ag/0.5wt%Cu | Rosin type flux | Max.1 time for iron soldering. |
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.