Cable Testing Equipment

UL Enamel Wire Probe 10 This probe is use to checking access to enamel coated wire accord to UL standard requirement. stainless steel with derlin handle.

IEC 60529 Jointed test finger 12mm, IP2X Material: metal, except where otherwise specified linear dimensions in milimeters tolerance on dimensions without specific tolerance: on angles: 0/-10° on linear dimensions: up to 25mm: 0/-0.05 over 25mm: +/-0.2 both joints shall permit movement in the same plane and the same direction through an angle of 90°with a 0 to +10° tolerance.

Test Probe D, ​IEC60529 Test Wire 1.0mm, IP4X Introduction: 1,According to: IEC61032:1997,IEC60529,IEC62368-1 2,Test Probe D is a necessary appliance for domestic and similar electrical appliance of against electric shock protection test. Technical parameters 1, Test Probe Length :100mm 2, Test Probe Diameter:1.0mm 3,Dam- sphere Diameter:35mm 4,Handle Diameter:10mm 5,Handle Length 100mm 6, According to IEC61032 figure 4 (the Test probe D) Application: 1, Standard test refers

IEC 60529 Test Sphere50mm , IP1X This probe is intended to verify the protection of persons against access to hazardous parts. It is also used to verify the protection against access with the back of the hand.

Test Needle Diameter : Ø0.5mm or Ø1mm, Length : 20mm

Telecom Test Probe Usage: Check access to telecommunications voltages. The Telecom Access Probe is required in IEC 60950, IEC 60065, UL and CSA Standards. It is used to check limited access to telecommunications voltages (TNV), mainly telephone jacks and operator areas. Satisfies basic standard for telecom product safety

UL Enamel Wire Probe 25 Usage: This probe is use to checking access to enamel coated wire accord to UL standard requirement. stainless steel with stainless stell handle.

UL Standard Articulated Finger Probe The UL Articulated Finger Probe is a standard articulated finger as required by Underwriters Laboratories in many of their standards. It is made of metal.

Test Rubber Ball Usage rubber ball used for dynamic stability testing to UL (USA) standards. A ball, 2 and 3/4/16 inch diameter (2.187 inches), filled with No. 60 core sand. It is suspended on a cord and allowed to swing as a pendulum to strike a surface. It is used for dynamic stability testing. Diameter – 2.187 inches (56mm) Weight – 0.33 lbs. (149 grams)

Test Hook​ Product information: The test hook complies with IEC60065. It is used to test whether the dangerous electric parts can be touched. The test hook is “hooked” into vents and seams in the enclosure & then pulled with a force (usually 20N). The hook has a hole at its long end, for use in conjunction with a PFI series Force Gauge. It is made entirely of stainless steel. Parameter: Width: 8mm Thickness: 1mm Length: 108mm Standard: IEC60065

Wedge Probe For Document Shredder The wedge probe is one of two new accessibility probes required by UL 60950 for paper shredders. UL found that children and small women could touch hazardous parts of some shredders. Calibration Certificate:Figure V.4 Wedge probe.pdf

Test Probe 11 , IEC61032-figure 7 Test Finger Probe , Unjointed test finger According to IEC61032 figure 7 1,Knurled Finger Diameter:12mm 2,Knurled Finger Length:80mm 3,Dam- board Diameter:50mm 4, Dam- board Length:100mm 5.M6 thread at the end of the probe(can be connected to the push-pull gauge) Packaging and Shipping 1. Aluminium box and carton box, careful and tight package, make sure the package is intact. 2. The package will be shipped by DHL/Fedex/TNT/EMS/UPS/China post

Test probe similar to test probe B of IEC 61032 with circular stop face Ø50 mm , IEC 60335-1 Test probe B According to IEC60335-1- clause 20.2. Test probe similar to test probe B of IEC 61032 with circular stop face Φ 50 mm 1.Knurled Finger Diameter:12mm 2.Knurled Finger Length:80mm 3.Baffle Plate Diameter:50mm 4.Baffle Plate Length:100mm 5.M6 thread at the end of the probe(can be connected to the push-pull gauge) Packaging and Shipping 1. Aluminium box and carton box,

UL507-Figure 8.2 Probe For Fan Impellers And Other Moving Parts Of Stationary Fans UL507-figure 8.2 Probe for fan impellers and other moving parts of stationary fans and fans intended to be permanently connected electrically Parameter: 1,Probe Length:106mm(4 inch) 2,Head Radius:R12.7mm(1/2inch) 3,Probe Diameter:25.4 mm(1 inch) 4,Handle Diameter:31.75 mm(1-1/4inch) UL 507 Electric Fans 8.3.2 A stationary or permanently connected fan shall be constructed so that any moving

UL507-figure 8.1 Probe for impellers of portable appliances ,Hazardous Moving Parts Probe Parameter: 1,Total Length:88.9mm(3.5inch) 2,Head Length:25.4mm(1inch) 3,Head Radius:R3.175mm(1/8inch) 4,Former Head Diameter:12.7mm(1/2inch) 5,Tail Diameter:25.4mm(1inch) UL 507 Electric Fans 8.2.5 Conventional designs of impellers meet the requirement of being guarded when: a) The relationship between mass (W) in kg, radius (r) in mm, and speed (N) in revolutions per minute is such that

Test Probe C, IEC60529 Test Rod 2.5mm, IP3X Introduction: 1,According to: IEC61032:1997,IEC60529,IEC62368-1 2,Test Probe C is a necessary appliance for domestic and similar electrical appliance of against electric shock protection test. Technical parameters 1, Test Probe Length :100mm 2, Test Probe Diameter:2.5mm 3,Dam- sphere Diameter:35mm 4,Handle Diameter:10mm 5,Handle Length 100mm 6, According to IEC61032 figure 3 (the Test probe C) Application: 1, Standard test refers to

IEC 60335-2-14 Test probe B of IEC 61032 with circular stop face with a diameter of 125 mm Parameter: 1,Jointed Finger Length:100mm(30/30/40mm); 2,Dam-board Diameter:125mm; 3,Standard:IEC60335-2-14|EN60335-2-14|GB4706.30 IEC60335-2-14|EN60335-2-14 Appliance: This test probe similar to that of test probe B of IEC 61032 but having a circular stop face with a diameter of 125 mm instead of the non-circular face, the distance between the tip of the test finger and the stop face

UL1005 Electric Flatirons -Figure 7.1 Probe 7.7 An opening in the enclosure of a flatiron located within 1 in (25.4mm) of the soleplate surface is acceptable if the probe illustrated in Figure 7.1 , when inserted point first, cannot be made to touch any uninsulated live part. Data to be calibrated Test Point Nominal Value (mm) Actual Value (mm) Deviation (mm) Limit (mm) Uncertainty (mm) P/F A φ31.8 ±0.159 B 75.0 ±0.375 C 15.9 ±0.1 D 0.81 ±0.05 E 6.4 ±0.1 F 3.2 ±0.1 Packaging

UL 1017 figure 25 Accessibility probe for opennigs 1.375 in(34.9mm) or more

UL 1278 Figure 10.1 Cone Test Finger Probe for Heating Elements Product details: This probe conforms to the standard requirement of UL1278 Fig 10.1. The handle is made of nylon while the probe is made of stainless steel. Standard:UL1278 Fig 10.1. Application:The heating element and any part of the element assembly (such as an element support, sheath and similar parts) shall be so guarded that flammable material as well as persons will be protected against contacting it. Test