Cable Testing Equipment

IEC 60529 Jointed test finger 12mm, IP2X Material: metal, except where otherwise specified linear dimensions in milimeters tolerance on dimensions without specific tolerance: on angles: 0/-10° on linear dimensions: up to 25mm: 0/-0.05 over 25mm: +/-0.2 both joints shall permit movement in the same plane and the same direction through an angle of 90°with a 0 to +10° tolerance.

Test Probe D, ​IEC60529 Test Wire 1.0mm, IP4X Introduction: 1,According to: IEC61032:1997,IEC60529,IEC62368-1 2,Test Probe D is a necessary appliance for domestic and similar electrical appliance of against electric shock protection test. Technical parameters 1, Test Probe Length :100mm 2, Test Probe Diameter:1.0mm 3,Dam- sphere Diameter:35mm 4,Handle Diameter:10mm 5,Handle Length 100mm 6, According to IEC61032 figure 4 (the Test probe D) Application: 1, Standard test refers

IEC 60529 Test Sphere50mm , IP1X This probe is intended to verify the protection of persons against access to hazardous parts. It is also used to verify the protection against access with the back of the hand.

Test Needle Diameter : Ø0.5mm or Ø1mm, Length : 20mm

Telecom Test Probe Usage: Check access to telecommunications voltages. The Telecom Access Probe is required in IEC 60950, IEC 60065, UL and CSA Standards. It is used to check limited access to telecommunications voltages (TNV), mainly telephone jacks and operator areas. Satisfies basic standard for telecom product safety

UL Enamel Wire Probe 25 Usage: This probe is use to checking access to enamel coated wire accord to UL standard requirement. stainless steel with stainless stell handle.

UL Standard Articulated Finger Probe The UL Articulated Finger Probe is a standard articulated finger as required by Underwriters Laboratories in many of their standards. It is made of metal.

Test Rubber Ball Usage rubber ball used for dynamic stability testing to UL (USA) standards. A ball, 2 and 3/4/16 inch diameter (2.187 inches), filled with No. 60 core sand. It is suspended on a cord and allowed to swing as a pendulum to strike a surface. It is used for dynamic stability testing. Diameter – 2.187 inches (56mm) Weight – 0.33 lbs. (149 grams)

6 Groups Cable Testing Equipment For Plug Static Pull Test For UL And IEC Standard 1. Quick Details: Alternative name Plug-line static tensile testing machine Function testing load strength between the plug terminal and power cord Feature Electric drive Weight 310kg Volume 91×55×99cm Test standard UL-817,IEC, GB 2. Product Summary: Plug-line static tensile testing machine is used for testing load strength between the plug terminal and power cord.The tester can test 6pcs

GB3048 General Conductor Resistance Test Device Product information: This device is the special appliance used for measuring the conductor resistance. It is applicable not only for the electrical wire whose length is 1 meter, but also the length of thousands meters. The design principle and the measurement accuracy completely conform to the standard requirement of GB3048. Technical parameters: 1) Power supply:AC 220V 50Hz； 2) Resistance measurement range:0.001mΩ～20kΩ 3)

IEC245-4 Cable Testing Equipment Rubber Electric Wire Abrasion Test Apparatus Product information: This device conforms to the standard requirement of IEC245-4. It is used for the abrasion test of the rubber insulated cables ( the power cables of the residential luminaire, household appliances such as electric cooker, electric kettle, electric iron.) Technical parameters: 1, Working power supply:AC220V 50Hz 2, Fixed shaft diameter:Φ40±0.3mm 3, Test rate:single trip 40±1 times

Chapter one: introduction of the instrument 1.1 Characters and main use This tester is used to perform the fatigue test on the AC and DC power cord and power cords lead. This is the necessary equipment for the QC department and Lab of the related industry. The rotating speed and rotating angle can be preset freely, and it will alarm once the specimen was damaged, it has many good features, such as: high accuracy, stable, and high efficiency, which is a perfect tester for

IEC60245-2 Figure 1 Cable Testing Equipment Flexible Cables Flexing Tester Product information: This cable tester is designed and manufactured in accordance with the standard requirement of IEC60245.2 clause 22.7. It is used for checking mechanical strength of completed flexible cables. This test does not apply to flexible cables with cores of nominal cross-sectional area greater than 4mm2and cables having more than 18 cores laid up in more than two concentric layers. This

IEC62262 Mechanical Strength Tester On Sheet Metal / Pendulum Impact Test Apparatus For Energy Impact Test Product details: This testing device conforms to IEC62262. It is used for the mechanical strength test of the sheet metal like the substation ark and the metalloid electric energy metering cubicle. The mounting bracket and the angle of impact are adjustable. This device is for the energy impact test (the energy is more than 2J). Technical parameters: Pendulum: Length:

UL486 Rotary Tensile Strength Test On Clamping Screw Terminal For Checking Damage Degree of Wire Product overview: This testing machine is also called the test apparatus for checking damage degree of wire which confirms to UL486 standard. This compliance is used for judging whether the design and the structure of the clamping screw terminal is correspondent with the requirement of non over-damage to the wire. Besides, it is also used to check whether the clamping screw

IEC 60884-1 Figure 8 Arrangement for Compression Test of 24.5 / 300N Manual Compression Test Apparatus Product details: The specimens are subjected to a compression test as shown in figure 8, the temperature of the pressure plate, of the base and of the specimens being (23±2) ℃ and the force applied being 300 N. The specimens are first placed in position a), as shown in figure 8, and the force is applied for 1 min. They are then placed in position b), as shown in figure 8,

IEC60335-1 Stability Test Turn Table With Digital Inclinometer / Inclined Plane Device Product information: This device is designed and manufactured in accordance with the IEC60335-1 clause 20.1.It is used to test the stability of an apparatus that requires a surface in order to work. The device consists of a surface and an angle adjusting device, with angles 0～15°adjustable. The appliance is placed in any normal position of use on a plane inclined at an angle of 10° to the

Temperature Measurement Heating Test Corner For Temperature Test Of Electronic Product Product information: The temperature measurement corner conforms to the standard requirement of IEC60950-1 : 2005. It is designed and manufactured to provide the required environment for the temperature rising test of all kinds of electrical, electrical products. It can be customized according to the different testing samples. The Black Test Corner for temperature measurement is conformed

JIS C3005 FIG.5-(b) Bending Twisting Test Apparatus / Three Stations Curve Torsion Machine (B)Bending twisting test Mount a sample of about 1m taked from the finished product,attach this to be a semicircle of r=60D to bending twisting test apparatus of FIG.5-(b).So that the rotor to the appropriate angle(θ,given to the number of time twisting around at a rate of per minute about 60 times ).At this time,not occur a short circuit between the lines,no crack about surface of the

JIS C3005 FIG.5-(a) Straight Twist Test Apparatus / Three Stations Linear Torsion Machine Twist test Twisting test is carried out by two types define their own way of our criteria. (A)Straight twist test Mount a sample of about 1m taked from the finished product,attach it to the straight twist test apparatus of FIG.5-(a).Given to the number of time twisting around at a rate of per minute about 60 times so that the rotor to the appropriate angle(θ).At this time,not occur a