Medical Test Equipment

ISO594-1 Fig 3b RING GAGE FOR MALE LUER CONNECTORS ISO594/1 Fig 3a or Fig 3b RING GAGE FOR MALE LUER CONNECTORS ISO 594 Has Been Replaced ISO 80369-7 Foreword ISO 80369-7:2016 cancels and replaces the first edition ISO 594-1:1986 and the second edition of ISO 594-2:1998, clauses, subclauses, tables, figures, and annexes of which have been consolidated and technically revised. The new ISO 80369-7 specification does not define any gauges. We still offer the ISO 594 Conical Ring

IEC 60601-1Grips and other handling devices-7 cm strap tester Carrying handles or grips furnished on PORTABLE ME EQUIPMENT shall withstand loading as described in the following test: The handles and their means of attachment are subjected to a force equal to four times the weight of the ME EQUIPMENT in any direction of NORMAL USE and transport. If more than one handle is furnished on PORTABLE ME EQUIPMENT , the force is distributed between the handles. The distribution of

ISO 80369-7 Figure C.2 Male Reference Luer Slip Connector and C.4 Male Luer Reference Connector ISO 80369-7 C.4 Male Luer Reference Connector Compatibility/Interchangeability: Between ISO 594/2 Fig 7 and ISO 80369-7 Fig C.4 The ISO 594/2 Figure 7 Male Luer Reference Conical Fitting is replaced by ISO 80369-7 Fig C.4 Male Luer Reference Connector. The ISO 80369-7 Figure C.4 is identical to the ISO 594/2 Figure 7 Reference Fitting. ISO 80369-7 Fig C.4 and ISO 594/2 Fig 7 are

KP-1000A mask virus filtration efficiency (VFE) detector Product introduction KP – 1000A mask the virus filtration efficiency (VFE) detector as the main performance index conforms to YY/T1497-2016 medical respirator material virus filtration efficiency evaluation phi-x174 phage test method, with double pneumatic contrast sampling method at the same time, improve the precision of sampling, applicable to the metrological verification department, research institutes, mask

ISO 80369-7:2017 Small-bore connectors for liquids and gases in healthcare applications - Part 7: Connectors for intravascular or hypodermic applications NOTE 1 Cone taper (0,06:1). NOTE 2 R may be 0,5 mm (maximum) × 45° chamfer. The minimum length of the male taper of 10,5 mm is required for testing non-interconnectable characteristics. A minimum length of the male taper of 7,5 mm may be used for the performance tests of Clause 6. ISO 80369-7-Figure C.2 — Male reference luer

ZR-1310model salt aerosol generator Product introduction ZR - 1310 salt aerosols generator is the use of collison nozzle will have a certain specific concentration NaCl solution after spray drying, particle size and concentration of aerosol dedicated instruments, built-in clean air compressors, dryers and more nozzle valve, electrostatic neutralizer, output aerosol concentration in 100 L/min to 1000 L/min air flow, be able to reach 100 mu g/L ~ 10 mu g/L, output aerosol

ISO 80369 - 3 2016 Small bore connector for liquids and gases in healthcare application - Part 3 Figure C.4 – Male reference CONNECTOR for testing female ENTERAL CONNECTOR for separation from axial load and resistance to overriding

ISO 5356-1 Anesthetic and Respiratory Equipment – Conical Connectors – Part 1: Cones and Sockets ISO 5356-1 Introduction In clinical practice, several breathing attachments used in anaesthetic and respiratory equipment may have to be joined together to provide a suitable breathing system. Items of medical equipment, such as a humidifier or a spirometer, are often incorporated into the breathing system which may also be connected to an anaesthetic-gas scavenging system.

ISO 5356-1 Anesthetic and Respiratory Equipment – Conical Connectors – Part 1: Cones and Sockets ISO 5356-1 Introduction In clinical practice, several breathing attachments used in anaesthetic and respiratory equipment may have to be joined together to provide a suitable breathing system. Items of medical equipment, such as a humidifier or a spirometer, are often incorporated into the breathing system which may also be connected to an anaesthetic-gas scavenging system.

ISO 80369-7 FIGURE C.4 and C.6 MALE LUER REFERENCE CONNECTOR ISO 80369-7:2016 cancels and replaces the first edition ISO 594-1:1986 and the second edition of ISO 594-2:1998, clauses, subclauses, tables, figures, and annexes of which have been consolidated and technically revised. Because of this, ISO 594 connections must be tested per ISO 80369-7 requirements. Read: Discussion on the change. Compatibility/Interchangeability... Between ISO 594/2 Fig 7 and ISO 80369-7 Fig C.4

Mask resistance tester 1.Test standard: yy0469-2011 medical surgical mask Differential pressure tester is used for pressure difference detection of surgical masks. The equipment is equipped with software, which can display pressure curve in real time, output test report and save test data. Meet the test standard yy0469-2011 surgical mask 5.7. YY/ t0969-2010, ventilation resistance 5.6 2. Features of equipment 1. The equipment is equipped with an air pump to simulate

1. Overview: The HME testing equipment is developed and designed according to ISO 9360-1 and ISO 23328-1. This equipment is mainly used to test the performance of the heat and moisture exchanger that simulates the human body, mainly measuring the water loss value during the use of the HME. 2. Specifications: The instrument is based on the standards ISO 9360-1, ISO23328-1; The instrument is mainly used to test the water loss of heat and moisture exchangers (HME) used in

Zr-1200model mask resistance tester Product introduction Zr-1200 mask resistance tester conforms to yy0469-2011 technical requirements for surgical masks.When different airflow flows through a certain area of the mask, the pressure at both ends of the mask can be detected to detect the resistance of the mask material. Executive standard YY/0469-2011 Technical requirements for surgical masks for medical use YY/T 0969-2013 Disposable surgical mask Related intellectual property

Respirator particle protection effect detector 1 Product introduction ZR - 1002 masks particle detector is protective effect on volume of 500 l self-purification test chamber was gb head mould, will be waiting for inspection masks worn on the head, by any quality median diameter was (0.6 + / - 0.050 mu m, in the salt concentration of 20 mg/m3 aerosols and mass median diameter was (0.3 + 0.050) microns, concentration of 20 mg/m3 of oily aerosol net input from the test chamber,

Moisture permeability tester Test standard: Surgical mask Synthetic blood penetration test for surgical masks synthetic blood penetration test for surgical masks can output test reports and store test data. GB 19083-2003-2011 GB/T 4745 requirements. Characteristics of the equipment 1. Configure funnel for detection. 2. The height can be adjusted within a certain range. Technical parameters of detector 1. Test height: 150±2mm. 2. Funnel height: 195±10mm. 3. Funnel diameter:

ISO8185 Respiratory tract humidifiers for medical use — Particular requirements for respiratory humidification systems Temperature sensors and mating ports DD.1 Dimensional requirements for temperature sensors Check dimensional accuracy as follows: a) Maintain the temperature sensor and gauge at ambient air temperature. b) Ensure that the axial length of the taper of temperature sensors is at least 10,5 mm. c) Engage the temperature sensor with the ring gauge shown in Figure

ISO8638 Cardiovascular implants and extracorporeal systems — Extracorporeal blood circuit for haemodialysers,haemodiafilters and haemofilters Figure 3 — Test device used for ISO blood port connector

ISO 80369-7:2017 Small-bore connectors for liquids and gases in healthcare applications - Part 7: Connectors for intravascular or hypodermic applications In Figure C.1, all outside edges of lug or thread form shall have a radius between 0,15 mm and 0,20 mm (unless otherwise specified). R may be × 45° chamfer. ISO 80369-7-Figure C.1 — Female reference luer lock connector for testing male luer connectors for leakage, separation from unscrewing, stress cracking and non

ZR-1210model respirator resistance detector Product introduction Zr-1210 respirator resistance tester is used to measure the inspiratory and expiratory resistance of the mask under specified conditions.It is applicable to the inspection and inspection of mask products by mask manufacturers and national labor protection equipment inspection institutions. Executive standard GB 2626-2019 Respiratory protective self-absorption filter respirator against particulate matter

ZR-1200model mask resistance tester Product introduction Zr-1200 mask resistance tester conforms to yy0469-2011 technical requirements for surgical masks.When different airflow flows through a certain area of the mask, the pressure at both ends of the mask can be detected to detect the resistance of the mask material. Executive standard YY/0469-2011 Technical requirements for surgical masks for medical use YY/T 0969-2013 Disposable surgical mask Related intellectual property