Medical Test Equipment

ZR – 1220 model Mask tightness tester Product introduction ZR - 1220 type respirator fit tester is a mask/respirator fit test of special equipment, at the same time compatible with OSHA and GB GB 19083-2010 medical respirator technical requirements of the respirator fit test on, widely applicable to mask manufacturers, the national labor protection articles inspection institution to related the mask products testing and inspection. Executive standard GB 19083-2010 Technical

Bacterial Filtration Efficiency (BFE) tester The main performance indexes of the mask bacterial filtration efficiency (BFE) tester not only meet the requirements of the test instrument of appendix B bacterial filtration efficiency (BFE) in YY0469-2004, but also meet the requirements of ASTM F2100, ASTM F2101, European EN14683 of the American Institute of Testing Materials. On this basis, innovative improvements have been made to improve the accuracy of the sampling by using

Body Upper-Carriage Module-IEC60601-1-Figure 33 , IEC60601-clause 9.8.3.3 loading tester 9.8.3.3 * Dynamic forces due to loading from persons Where dynamic forces (due to sitting down, standing up, PATIENT handling PROCESS or the like) can be exerted on ME equipment parts intended to support or suspend a PATIENT or OPERATOR in NORMAL USE, the ME EQUIPMENT shall maintain BASIC SAFETY and ESSENTIAL PERFORMANCE. Compliance is checked by the following test: Prior to performing

ISO 5356-1 Anesthetic and Respiratory Equipment – Conical Connectors – Part 1: Cones and Sockets ISO 5356-1 Introduction In clinical practice, several breathing attachments used in anaesthetic and respiratory equipment may have to be joined together to provide a suitable breathing system. Items of medical equipment, such as a humidifier or a spirometer, are often incorporated into the breathing system which may also be connected to an anaesthetic-gas scavenging system.

601 / 990 Contact current-terminal discharge tester Technical specification Type 601 Contact current-terminal discharge tester... 1, overview This instrument is a , information technology equipment and electronic and electrical contact current, leakage current and terminal discharge instrument.Contact current (leakage current) and terminal discharge volume are general measuring instruments in the laboratory engaged in electronic and electrical product safety testing, widely

ISO 14457 Dentistry — Handpieces and motors , ISO 14457 -Figure 3 Five types of test mandrel Test mandrel The test mandrel shall have the dimensions shown in Figure 3. The shape of the shank end for all types of test mandrels shall be either conical or rounded at the discretion of the manufacturer or test house to avoid damaging of the chuck system. The mandrel cylindricity shall not exceed a value of 2,5 µm and its hardness shall exhibit a value of at least 610 HV5. Test in

Cone tool | medical bed standard equipment It is designed according to the standard iec60601-2-52 figure 201.103a. It is made of aluminum and weighs 5.13 ± 0.05kg Model KP-61521 According to standard IEC 60601-2-52-Figure 201.103a Total weight 5.13 ± 0.05kg Surface roughness 1.6 Material Aluminum

IEC60601 Figure CC1,Which Is Used To Evaluate The Risk Degree Of V-Shaped Opening Of V-Shaped Opening Of Medical Devices Triangle tool conforms to iec60601-2-52 figure CC. 1, which is used to evaluate the risk degree of V-shaped opening of medical devices. The tested area is V-shaped opening of B and C. the tool is made of aluminum and its mass is 3.34kg

IEC60601-2-52 Entrapment test tools | Cylinder tool Cylinder tool | IEC60601-2-52-Figure 201 .103 b Cylinder tool Key 1 Total weight 3,34 kg ±0,05 kg 2 Marked centre line 3 Surface roughness 1 ,6 4 Drilling hole for weight adjustment Figure 201 .1 03 b) – Cylinder tool schematic

ISO 80369-7 Fig C.2 Male Reference Luer Slip Connector for testing female Luer Connectors for leakage Escape Clause: ISO 80369-7; Page 24; Annex C; Figure C.2; Note 2 states: The minimum length of the female taper of 10,5 mm is required for testing non-interconnectable characteristics. A minimum length of the female taper of 7,5 mm may be used for the performance tests of Clause 6. What they are saying here is that if you use an ISO 594/1 Fig 5 Reference Fitting with a

Loading pad | IEC60601-2-52-Figure 201 .1 04 Loading pad 201 .5.1 02 Loading pad The loading pad (see Figure 201 .1 04) is a rigid circular object, (355+/–5) mm in diameter, the face of which has a convex spherical curvature of 800 mm radius with a 20 mm front edge radius. Figure 201 .1 04 – Loading pad

Cone tool | IEC60601-2-52-Figure 201 .103 a cone tool Key 1 Total weight 5,1 kg ±0,05 kg 2 Marked centre line 3 Surface roughness 1 ,6 4 Drilling hole for weight adjustment Figure 201 .1 03 a) – Cone tool schematic

ISO80369-3 Figure C.3 Gauge Male Reference CONNECTOR For Testing Female ENTERAL CONNECTOR For Leakage Product Specifications Brand Name Kingpo Material Hardness Steel Standard ISO 80369-7 Hardness HRC58-62 Warranty 1 Year Product Name LUER GAUGE Product Description ISO 80369-3 2016 Small bore connector for liquids and gases in healthcare application - Part 3. Figure C.3 - Male reference CONNECTOR for testing female ENTERAL CONNECTOR for leakage, disconnection by unscrewing,

Cylinder tool | IEC60601-2-52-Figure 201 .103 b Cylinder tool Key 1 Total weight 3,34 kg ±0,05 kg 2 Marked centre line 3 Surface roughness 1 ,6 4 Drilling hole for weight adjustment Figure 201 .1 03 b) – Cylinder tool schematic

ASTM F2554 22 Phantom

Product Description IEC 60601-1-Figure 33 Body upper-carriage module 9.8.3.3 * Dynamic forces due to loading from persons Where dynamic forces (due to sitting down, standing up, PATIENT handling PROCESS or the like) can be exerted on ME equipment parts intended to support or suspend a PATIENT or OPERATOR in NORMAL USE, the ME EQUIPMENT shall maintain BASIC SAFETY and ESSENTIAL PERFORMANCE. Compliance is checked by the following test: Prior to performing this test, the PATIENT

ISO/DIS 18193:2020- Cardiovascular implants and artificial organs — Cannulae for extracorporeal circulation ISO/DIS 18193:2020-Figure A.3 Gauges for testing 6% (Luer) conical fittings Packaging

IEC 80601-2-60 loading fan construction Standard: IEC80601-2-60-figure AA.4 Packaging and Shipping 1. Aluminium box and carton box, careful and tight package, make sure the package is intact. 2. The package will be shipped by DHL/Fedex/TNT/EMS/UPS/China post/EF-Express/Special line, as you have chose in the order. 3. The shipping time is different, it depends on the distance bewteen us. At usual, exclude the preparing time, the goods would be sent to you in 5days.

ISO10079-1:2015 Test Equipment List ISO10079-1:2015 Test Equipment List Clause Name Test Name Note 6.1.2&7.5.2 Container capacity: (ISO10079-1, Sub-Clause 6.1.2) &Overflow protection of electrical suction equipment: (ISO10079-1, Sub-Clause 7.5.2) 6.1.3 Container strength: (ISO10079-1, Sub-Clause 6.1.3) 6.3.1 Degree of collapse of Suction tubing: (ISO10079-1, Sub-Clause 6.3.1) Figure A.2 — Test apparatus for degree of collapse for suction tubing 7.5.3.1 Negative pressure

Loading pad- Medical Bed tester Model KP-61523 According to standard IEC 60601-2-52-Figure 201.104 Total weight 1500N The equipment consists load pad + stainless steel drum + load steel ball Material Aluminum + stainless steel Size Φ335*500mm Standard drawing