Toys Testing Equipment

ISO 8121-4 2014 Electroplating Steel Loads For Ride On Toys And Seats Overload Test Product Information Place the toy on a horizontal plane. Load the toy on its standing or sitting surface with the appropriate mass in accordance with below table Conduct the test for overload requirements so that it will be consistent with the advertised mass capacity of the toy, if that mass is higher than the required load according to below Table. Determine whether the toy collapses such

45 Degree Automatic Flammability Testing Equipment Description 45 degree flammability tester, check the flammable performance of the textile Stainless testing room with glass window, after ignition automatic time (0.01 second precision) automatic Parameters Manual firing device, included sample holder and bush. Spread time scope 0-99.99s, Firing time: 1s or specified, resolution: 0.01s Igniter model comply to ASTMD1230 Dimension 400mm×300mm×500mm Weight 28kg Power 220V/50Hz

Surface Flammability Tester The surface flammability Tester commonly used in the examination down or the superficial knowledge fabric's flammability, the flame spreads fast in the fabric surface, but the fabric Kieb structure is incombustible. Technical specifications Nozzle movement speed 150 millimeters/second ±5 millimeter/seconds (bidirectional) The nozzle moves the distance ≥300 millimeter May test the fabric plush altitude 0-70mm; Flame altitude: 0-60mm continuously

ASTM F 963 4.21 Alu.alloy Pacifier Test Fixture/Toys Safety Testing Equipment Application To determine whether the pacifiers for infants present choking or suffocating hazards. A pacifier is placed centrally in the opening of test fixture. The nipple is subjected to a tensile force of 2 lbs and held for 10 seconds. If the shield is pulled through the fixture, the pacifier has failed. Testing Standards 16 CFR 1510 ASTM F 963 4.21 EN71

Compression Head To simulate the subjecting of a toy to mechanical damage through compressing or other action likely to be performed by a child. After testing, the toy may be tested for sharp edges, sharp points & small parts. ASTM Compress Head Standard:ASTM F 963 8.10.1 EN Compression Head Standard EN71-1998 8.8 dimension :28×28×19mm Diameter 30 mm round rod

EN 71 Impact Flooring Medium Product information A standardised surface onto which a toy can be dropped from a certain height to simulate possible damage which may occur by falling from a crib, table or counter top or other impact situations. After testing, the toy is examined for possible hazards such as sharp edges, sharp points and small parts. Specification:2mm Rubber+4mm SST Sheet 600mm×600mm Standard EN 71 Key Specification Steel Plate Thickness 4mm Rubber thickness 2mm

Wood Material ASTM Tumble Test Steps 6 Layers For Wheeled Toys Description It is used for Tipover Test for Large, Bulky Toys—Large, bulky toys shall be tested for impact by tipping over three times, one of which is in the worst attitude by pushing the sample slowly past its center of balance onto the impact medium described in 8.7.3. Technical parameters “A” shall be not less than 3ft (9.4mm) “B” shall be not less than 7in (180mm) “C” shall be not more than 9 in (230mm) Key

ISO 8124-4 Impact Head from swing elements (without Accelerometer) Product Information Test mass, consisting of an aluminium sphere or semi-sphere of radius 80 mm ± 3 mm, and a total mass (including accelerometer) of 4,6 kg ± 0,05 kg. The impacting part between the surface struck and the accelerometer shall be homogeneous and free from voids. Cables connected to the accelerometer shall be placed in such a way that the effect on the mass of the test mass is minimized Test

EN71-1 Toys Testing Equipment Noise Testing Stand Application This machine is the test stand for noise meter, used to assist in measuring the volume decibel produced by sound toys in a predetermined distance, then minimize the possibility of hearing damage that might be caused by toys that are designed to produce sound. Energy along the X, Y, Z (X displacement: 0-100CM; Y displacement of 0-170CM; Z displacement: 0-180CM) slide freely positioning the three directions. Flat

ASTM Toys Testing Equipment Flexure Test Fixture Product information To determine whether metallic wires or materials used for stiffening or retention of form in toys can be easily bent or broken. Potential hazards of sharp points & sharp edges. Used to test the toys from the increase in rigidity or fixed shape of the metal wire or other metal materials used in the bending (or abuse) the process, whether due to fracture a risk of a sharp tip or sharp edges protruding. Abuse

Hasbro Standard Rattle Test Fixture / Baby Rattles Tester Product Information To determine whether rattles for infants of up to 18 months old present choking or suffocating hazards. The rattle is placed in the opening of test fixture. If any part of the rattle can pass through the opening without being pushed or pulled, the rattle has failed. For other rattles incorporating nearly spherical, hemispherical or circular flared ends, a Supplemental Rattle Test Fixture is

ISO8124-1 Toys Testing Equipment Alu.Alloy Supplemental Test Fixture Product Information To determine whether rattles for infants of up to 18 months old present choking or suffocating hazards. The rattle is placed in the opening of test fixture. If any part of the rattle can pass through the opening without being pushed or pulled, the rattle has failed. For other rattles incorporating nearly spherical, hemispherical or circular flared ends, a Supplemental Rattle Test Fixture

EN 71 Toys Testing Equipment Liquid Leakage Testing Needle Product Information Diameter 1MM , the top radius 0.5MM, load 5N , for leakage teating. Standard EN71-1; GB6675 A.5.19 Dimension Tolerance + /-0.05mm Testing Standards ISO 8124-1 ASTM F963 EN-71 Procedure Within 30 s of removing the toy from conditioning, apply a force of (5+0.50)N to the external surface of the toy through a steel needle with a diameter of 1 mm 0,1 mm and with a tip radius of 0,5 mm 0,05 mm. How do

ASTM Toys Testing Equipment Toy Steel Ball Dropping Impact Tester Product information Steel Ball Dropping Impact Tester is to test the impact endurance of brittle material like Plastic, Ceramic, Acrylic, and glass. To perform impact test for toys that cover the face (like Mask). Comply with ASTM F963 8.7.4, ISO 8124-1 5.14, GB 6675 A. 5.14 Drop ball impact testing machines provides a standard steel ball which be adsorbed by magnetic force, and when cut off the power supply to

ISO8124-4 Toys Testing Equipment Probe D (Larg Head ) for assessment of completely bound openings Probe D is used for testing for head and neck entrapment. Aplication Activity toys with accessible completely bound openings with a lower edge of 600 mm or more above the ground or any other surface which is of such a size that it will support a child, shall be assessed using probe Procedure First insert probe C and then probe D and examine whether they protrude more than 100 mm

EN71-8 Toys Testing Equipment Probe D (Large Head ) for Assessment of Completely Bound Openings Probe D is used for testing for head and neck entrapment. Aplication Activity toys with accessible completely bound openings with a lower edge of 600 mm or more above the ground or any other surface which is of such a size that it will support a child, shall be assessed using probe Procedure First insert probe C and then probe D and examine whether they protrude more than 100 mm

EN Toys Safety Testing Equipment Probe C (torso) for Assessment of Completely Bound Openings Probe C is used for testing for head and neck entrapment. Aplication Activity toys with accessible completely bound openings with a lower edge of 600 mm or more above the ground or any other surface which is of such a size that it will support a child, shall be assessed using probe Procedure First insert probe C and then probe D and examine whether they protrude more than 100 mm

Scooters Toys Testing Equipment Slope Stability Tester Toy Scooters Brake Proformance Tester.pdf Application Stability of activity toys with a free height of fall of 600 mm or less. Load the toy in the most onerous position with a mass of 50 kg+/-0,5 kg on its standing or sitting surface for 5 min. For toys labelled as not suitable for children 36 months and over, load the toy with a mass of 25 kg+/-0,2 kg. Place the toy on a 10°+/-1°slope in the most onerous position with

ISO 8124-1 Toys Testing Equipment Hand Held Dial Torque Gauge Product introduction To determine whether components of toys can be removed by a certain torque force. A torque-measuring device is used in conjunction with a torque clamp to record the applied force. Any projection, part or assembly of a toy that a child can grasp with at least the thumb & forefinger or the teeth shall be subject to the torque test. Testing standards ASTM F963 CFR 16 CFR CPSC USA EN71, ISO8124

ISO 8124-1 Toys SafetyTesting Equipment Small Parts Cylinder Product information To determine whether toys & other articles intended for use by children under 3 years old present choking, aspiration, or ingestion hazards because of small parts. If any objects can fit completely into the cylinder without compressing & in any orientation, it is defined as a "Small Part". Its internal dimensions simulate the fully expanded throat of a child under 3 years old. Technical