Toys Testing Equipment

Kids Toys Tester EN Flexure Test Fixture , Aluminum Alloy Toys Safet EN71 Flexure Test Fixture Product Information To determine whether metallic wires or materials used for stiffening or retention of form in toys can be easily bent or broken. Potential hazards of sharp points & sharp edges. Testing Standard EN71-1 Note 1.Independent carton packaging 2.In Stock

Figernail of IEC 60335-1:2010/Thrust Standard Test Nails Overview It is mainly used for the penetration prevention of sharp parts of solid insulation, and for non-detachable parts to prevent contact with live parts, waterproof or contact with moving parts. It is fixed in a reliable manner and should withstand the mechanical stresses that occur in normal use buckles. Standard According to IEC60335-1 standard. Technical parameters of standard test nails 1. Components:

EN14350-1 Aluminum Alloy Pacifier Fixed Safety Test Fixture Usage Need to be installed on the tensile machine Product Information Secure the bottle at a 45° angle to the spindle and clamp the nipple or the end of the drinking unit 10 ± 2 mm. Apply 60±5N at a speed of 200±5mm/min in the direction of 45° with the nipple spindle for 10 sec. Check if the nipple or drinking part is broken.

ASTM F963 ​Nail Bed Flammable Tester Used in the detection part of the combustion of flammable hair, and record the time, to see whether the burning of part of the meet flammability standards dimension:25.4*25.4cm. standard:ASTM F963 ；

EN1400-2 EN14350-1 EN14372 EN1400-1 Indentor For Pacifier Testing Usage A range of fixtures for pacifier testing, including acupuncture, bending, tensile testing, etc. Standards compliant EN1400-2, EN14350-1, EN14372, EN1400-1 Technical parameters The needle part is 0.20±0.01MM on the front and DIN3±0.05MM on the side. 1. Need to be installed on the tensile machine 2. The lower nipple fixing fixture can be moved left and right to facilitate testing different parts of the

Small Ball Test Fixture Use Small ball test fixture is use to examine a toy up of whether small ball accessories may result in the child swallow, stop breath way and esophagus to cause choking danger or not Standard test US 16CFR 1510, ASTM F 963 4.6.2, EU EN71-1998 8.16. Parameter Material: Aluminum alloy Volume: 72.6 × 72.6 × 6.35 mm Weight: 64 g How to use and understand 1. Place the ball in the position where it is most likely to be allowed to pass the ball test template

ISO 8124-1 2014 Stainless Steel Protrusion Test Gauge Technical Parameter Material Stainless steel torerances+/-0.1mm 1.Inner diameter 13mm Outer diameter 25mm Thickness 6mm 2.Inner diameter 26mm Outer diamter 38mm Thickness 12.5mm 3.Inner diameter 38mm Outer diameter 50mm Thickness 19mm 4.Inner diameter 77mm Outer diameter 89mm Thickness 38mm ISO8124-4 Clause No. 6.7.1.2 IS 9873-4

Stainless Steel Self-Retracting Ropes Tester Applications Used to test the force of self-retraction mechanisms for self-retracting cords toys. Using a suitable clamp, position the toy so that the cord is vertical and the toy is in the most favourable position for retraction. Extend the cord fully and attach a mass of (0,9 ~:g5 )k9. For monofilament cords less than 2 mm in diameter, attach a mass of (0,45 +g:g5 )k9 . Determine whether the cord retracts more than 6,4 mm.

Electroplating Steel Loads for Stability Test Product Information Apply the load so that the major axis is perpendicular to the true horizontal while the toy is on the specified incline. Design the load so that the height of its centre of gravity is (220 ± 10) mm above the seat surface. For toy scooters, however, use a test load with dimensions as specified in Figure 30. For all ride-on toys, secure the centre of gravity of the load both (43 ± 3) mm rearward of the frontmost

Improvised Projectile Test Tool as Per Hasbro SRS 045L Description Determine through experimentation if discharge mechanism is capable of discharging projectiles other than the projectile specifically designed for use with the discharge mechanism. Testing of improvised projectiles shall include, but is not limited to, the following objects: Types of improvised projectiles A) Pen and Marker Caps B) Pens, Pencils and Markers C) Paper Clips D) Pen Refills E) Batteries F) Marbles

ISO 8124 Toys Testing Equipment Toy Lids Durability Tester Application This instrument is used to detect the durability test of the toy case cover. Use method and judgment: One end of the reciprocating structure of the instrument is connected to the side of the lid remote from the side of the hinge, and the cover is opened and closed by the reciprocating motion of the mechanism until the number of tests reaches the set value. To determine whether the cover and cover support

ISO8124-1 Toys Testing Equipment Brake Tester for Toy scooters and Baby Carriage Application Stability of activity toys with a free height of fall of 600 mm or less Load the toy in the most onerous position with a mass of 50 kg+/-0,5 kg on its standing or sitting surface for 5 min. For toys labelled as not suitable for children 36 months and over, load the toy with a mass of 25 kg+/-0,2 kg. Place the toy on a 10°+/-1 slope in the most onerous position with respect to

ISO8124-4 Durability Tester for Suspension Connector of Swings Product information Suspension connectors and means of suspension are cycled 180 000 times under load to simulate use. For the safety of children when they are playing on swings, a durability test machine is recommended to check if the suspension connector is robust enough after many times of use. Procedure Attach each type of swing element to its support member in accordance with the installation instructions,

Motor Brake Performance Testing Ramp Applications This Motor Brake Performance Tester is a longer 10 degree ramp, mainly used for the brake test of electric ride-on toys. Standards EN-71-1 Specification Ramp degree 10 ± 1 degree Testing surface Aluminium oxide P 60 Demension(L×W×H) 400×122×86 Weight 300kg Procedure Motor brake performance – Ramp test Load the toy as in 8.21 (static strength) and place it on a plane inclined at (10 ± 1)° covered with a surface of abrasive

ASTM Toys Testing Equipment Toy Steel Ball Dropping Impact Tester Product Information Steel Ball Dropping Impact Tester is to test the impact endurance of brittle material like Plastic, Ceramic, Acrylic, and glass. To perform impact test for toys that cover the face (like Mask). Comply with ASTM F963 8.7.4, ISO 8124-1 5.14, Drop ball impact testing machines provides a standard steel ball which be adsorbed by magnetic force, and when cut off the power supply to magnetism, the

EN71 Test Round Rod Use: The SL-S39 test round bar is used to test moving parts clearance and accessible tests that may damage your fingers. Instructions: The round rods of the standard requirements are inserted into the gap of the toy to be tested. If it can be inserted, it is judged to be accessible. Standard test: EN71. Parameter: Specifications: diameter is 3mm, 5mm, 7mm, 12mm; tolerance: +-0.5mm.

Dial Force Gauge Feature Simple operation Precision Peak value maintance Indicate two scales Handheld design Compact Easy operation Application electrics Components of Vehicle, Lighter & portfire , construction, fabric etc Capacity 10KG,20KG,30KG,50KG

Skyline SL-S44 Load for Determination of Dynamic Strength 50kg Test Load 50kg Test Load Load for determination of dynamic strength. Test load for scooters intended for children with a body mass of between 20 kg and 50kg. Specification Part weight(Kg) diameter(mm) height(mm) a 10.42 150±2 75±2 b 14.58 178±2 75±2 c 4.16 d 2.00 e 0.50 Testing Standards EN71, ISO8124-1

25kg Test Load Load for determination of dynamic strength. Test load for scooters intended for children with a body mass of between 20 kg or less . Specification Part weight(Kg) diameter(mm) height(mm) a 10.42 150±2 75±2 c 4.16 d 2.00 e 0.50 Testing Standards EN71, ISO8124-1

Toggle Test Device Application It is used to check whether the toys' gap of children to confirms the safety requirement. Testing procedures 1. The hinge line clearance When the fixed parts of the toys and the movable parts which are over 0.25KG have gap in the hinge line, all the parts in the hinge line should be inserted into the round bar of φ12mm if the the gap can be inserted into the round bar ofφ5mm. 2. the round hole in the rigid material. For the accessible round hole