Decoiler Straightener Feeder

Mechanical NC feeder feeding speed, high-speed gear replacement feeder high-precision feeding The principle of the NC feeder is that the servo motor and the PLC control system drive the timing belt to drive the upper and lower rollers to rotate and press loose to achieve quantitative feeding. Advantages of NC feeder: Double control mode of button and touch screen, easy to operate, servo control, higher feeding accuracy, and multi-stage feeding. It is convenient to set the

Roller feeder feeding accuracy, stamping and leveling machine, punch feeding process Roller feeders are favored by stamping customers for their high efficiency, high precision, low energy consumption, high cost performance and low failure rate. It is only necessary to ensure long-term high efficiency and stability during the long-time high-load stamping and feeding process, reducing downtime, and it is inseparable from reasonable maintenance and correct operation. Only

Automatic stamping, high-precision stamping materials, two-in-one rack and leveling machine In the automated stamping production process, in order to ensure the quality of stamped products, high-precision punching, feeding equipment and molds are required, as well as high-quality stamping materials. Therefore, before stamping, the material must be leveled to eliminate its internal stress and improve its flatness. The two-in-one material rack and the leveling machine are

Feeder precision feeding, stamping processing automatic feeder, yaw type NC feeder The yaw type NC servo feeder is developed on the basis of the original ordinary NC feeder. The automatic feeding machine for stamping processing optimized by special typesetting method can realize multiple yaw to save raw materials and improve production efficiency. Pivot NC servo feeding range: It is mainly used in the processing of stamping products such as screens, caps, motor stators and

There are many factors affecting the feeding accuracy of the roller feeder. In addition to the inertia problem caused by continuous feeding, the machining accuracy of the gears, the left and right wall panels and the one-way device, the reverse device, and the brake device all affect the feeding accuracy. Ruihui Machinery is in the production of roller feeders to ensure its accuracy, paying close

Air feeder punching automatic feeding, punching equipment leveling feeder, automation The air feeder quick connector is connected to the air valve and the high pressure pipe, and is a joint that can connect or disconnect the air pressure pipe without tools. 1. The air feeder quick joint air pressure range is from 1kg/cm to 10kg/cm. 2. The actual number of disassembly and assembly in the actual stamping process can be up to 100,000 times. 3. the air feeder quick connector plug

NC feeder installation position, feed height of punch feeder, punch press feeding 1. Determine the installation position of the NC feeder according to the feeding direction requirements. 2. Hang the punch positioning block of the NC feeder fixing plate on the workbench of the punching machine. Note that the center line of the fixing plate and the center line of the punching plate of the punching machine should be aligned. Then tap the M14 thread on the punching table and lock

The air feeder, roller feeder and NC feeder are three kinds of feeding equipment commonly used in the stamping production line. Compared with the roller and NC, the air feeder has a high failure rate, poor feeding accuracy and a small use range. It is easy to cause material damage, and the disadvantages of high maintenance cost are gradually eliminated by the market. The roller feeder and NC

1. After the NC feeder feeding parameter setting is completed, if it is not necessary to change the feeding length, just enter the operation screen after booting, press F6 to switch to the automatic state, and start production. 2. For the need to control the press, it is necessary to connect according to the needs of the site. The 220V solenoid valve or electromagnet can be used to set the

Press stamping and guiding device, NC feeder feeding height, automatic process 1. Determine the installation position of the NC feeder according to the feeding direction requirements. 2. Hang the punch positioning block of the NC feeder fixing plate on the workbench of the punching machine. Note that the center line of the fixing plate and the center line of the punching plate of the punching machine should be aligned. Then tap the M14 thread on the punching table and lock

The hydraulic heavy-duty material frame is optimized by adding hydraulic cylinders and pressure arms to the standard heavy-duty material frame MT, and is used for unwinding and discharging of heavy-duty coil materials in the stamping production line. It consists of a base, a disc brake system, a tile and an overhanging bearing. It is a single-roll cantilever structure. The material frame has

The clip feeder is driven by a cam and uses a curved cam and three plate cams to achieve high-speed and smooth feeding. Built-in inspection mechanism to detect blockage or deformation of materials. The 165 degree feed section angle allows the material to stay longer in the press. Combined with the mold guiding pin, the release time of the material during guiding can be adjusted. It can

This series nandles material form 600mm to 1,300mm wide and up to 6.0mm thick. The 11 work rolls offer an extraordinary level of flatness to the materials. The HL series featured that adapting all rolls driven with universal joint (MAC4-F) and strengthen body flame for straightening high tension materials. A straightener port opening mechanism has been added. allowing for improved

Standard Features Motorized uncoiler Variable speed operations Hydraulic mandrel expansion Pneumatic disk brakes Pneumatic pressing arm A frame for loacting the coil Electric eye type loop control 11pcs straightener rolls Worm gear adjustment of upper rolls Servo-driven feeder-straightener Options Hydraulic coil car Special expansion range Automatic oiling unit Hands-free input supporting

This series nandles material form 600mm to 1,300mm wide and up to 6.0mm thick. The 11 work rolls offer an extraordinary level of flatness to the materials. The HL series featured that adapting all rolls driven with universal joint (MAC4-F) and strengthen body flame for straightening high tension materials. A straightener port opening mechanism has been added. allowing for improved maintenance and

This is a compact feeding line, with decoiler, straightener and feeder machine in one combination unit. It used to uncoiling metal strip from coil stock, straightening it to required flatness and feed it to press machine for stamping process. Thanks to a well-knit body and advanced mechanical structure, it can easily handle coil stock up to 10tons. With YASKAWA servo drive, YASKAWA servo

Product Application: 1. This big machine combines uncoiler function, straightener function, NC servo roll feeder function together, so as 3 in 1. 2. It can decoil suitable metal sheet coil, then straighten the metal sheet, then feed the metal sheet to press machine automatically, for automatic stamping processing. Main Features: 1. Flexible operation: All the functions of the feeder are

Metal Sheet Coil Feeder Decoiler Straightener Feeder For Hydraulic Press 25 Ton Standard features: 1. advanced material arc control system 2. feeding correction roller wheel and chrome plated hardware 3. leveling head using manual 4. precision leveling ring volume is displayed as the scale 5. rack fit with brake hold 6. can flip the wheel sets of device 7. rack adjustment is block device 8. leveling part of the whole dirve 9. loading trolley unit Specification: Model MAC2-400

Product Description: Using in Metal stamping line especial good in auto parts . Suitable for coiling and uncoiling straightening feeding. Adjustable brake device and strong roller make the material coiling smooth . Import Japan magnetic motor and electronic components. Specification: Model MAC2-400 MAC2-500 MAC2-600 MAC2-800 Stock Width(mm) 50-400 50-500 50-600 50-800 Stock Thickness(mm) 0.3~3

Sheet Metal Uncoiler And Decoiler Straightener Feeder With Power Press Machines STANDARD ACCESSORY 1. Acluster gear set maximizes transmissions of horsepower 2. Outgoing catenary to assist and support the material 3. Feed and Straightener rolls with a hard chrome finished 4. Feeding line easily adjusts by advance worm gear screw jacks device 5. Straightener adjusts by advance worm gear screw jacks device 6. Left/right swing tension roll support device 7. Reference indicator