Vehicle Testing Equipment

IEC 62196-1 5000N&11000N Vehicle Drive Over Testing Apparatus for Vehicle Connector and Plug Product Information For Vehicle Drive Over Testing Apparatus: Applied standard & clauses: IEC 62196-1: 2022 clause 33. The test equipment is used to check whether a plug or vehicle connector shall have adequate resistance to damage from being driven over by a vehicle, unless it is provided with a cable management system which prevents the accessory from being left on the ground. Test

IEC 62196-1 EV Charging Plug And Socket Withdrawal Insertion Force Test Equipment Product Information For EV Charging Plug And Socket Withdrawal Insertion Force Test Equipment: IEC62196-1:2014 "Plug,socket-outlets,vehicle couplers and vehicle inlets–Conductive charging of electric vehicle-Part1:Charging of electric vehicles up to 250A a.c and 400A d.c". Samples and Restrictions: New energy charging vehicle plug, locking device between vehicle sockets and plug socket connector

IEC61851-1 EV Conductive Charging System Static Load Test Bench Product Information For Static Load Test Bench: Comply with the standards and clauses of EN IEC 61851-1-2019, IEC 61851-1-2017. Used for mechanical strength test of electric vehicle charging piles and similar power supply equipment shells for charging vehicles Test principle: Drive the electric cylinder through the servo motor to apply a certain force value to the top and side of the sample according to the

IEC 61851-1 Stainless Steel Test Rod Probe D Test Probe With Alligator Clip Product overview: This rod probe is intended to verify the protection of persons against access to hazardous parts. It is also used to verify the protection against access with a wire. Applicable standard This probe conforms to the standard requirement of IEC61032 figure 4 test probe D, it is required by IEC 61851-1 clause 8 and 12.4, IEC 60335-1 clause 22.1, IEC60529 for IP4, IEC60065 and etc.

IEC 62196-3 Clause 9 Universal Material Tensile Machine 2KN For Wire And Cable Tensile Test Product Overview This universal tensile testing machine with customized fixtures is designed to perform testing according to IEC 62196-3:2026 clause 9, IEC 62196-1:2025 clause 9, 13.3.2, 16.9, 26.7.3, table 6, BS1363-2 clause 11.10.7, 13.11.4, and other relevant standards. Computer-controlled and widely used for mechanical performance testing of various materials including rubber,

IEC 62196-3 Vehicle Connector And Plug Mechanical Endurance Test Machine For EV Charging Plug Test Product Overview The EV Charging Plug Mechanical Lock Endurance Test Equipment is a programmable testing system developed for evaluating the mechanical, electrical and operational durability of EV charging interfaces, plugs, sockets and couplers. Designed around the relevant requirements of IEC 62196-3:2022 and IEC 62196-1:2022, the system simulates repeated real-world operation

IEC 62196-1 EV Charging Plug And Socket Withdrawal Insertion Force Test Equipment for Connectors The EV Charging Plug Insertion & Withdrawal Force Tester is a specialized mechanical testing system designed to evaluate the insertion force and withdrawal force of electric vehicle charging plugs, sockets and vehicle connector interfaces. Developed for testing requirements associated with IEC 62196-1 , the system provides a controlled and repeatable method for measuring the force

EV Charging Connector Comprehensive Testing System For AC Type 2 And DC CCS2 Product Overview This testing system is specifically developed for comprehensive performance verification of AC Type 2 and DC CCS2 charging connector cable assemblies. It enables fast, accurate, and fully automated inspection of finished charging connectors to ensure product quality and compliance with manufacturing requirements. Each charging connector can be linked to a unique QR code for

IEC 62196-1 Short-Time Withstand Current Test System For EV Charging Guns & Circuit Breakers The Short-Time Withstand Current Test System is professional equipment for short-circuit withstand current testing of EV charging guns, circuit breakers, distribution transformers, ring main units, cable branch boxes, connectors and other electrical devices. It fully meets the short-circuit current withstand capability verification requirements of IEC 62196-1:2025 . This system adopts

IEC 62196-1 Automatic Charging Gun Cable Torsion Test Machine For EV Charging Gun Cables Testing Product Overview Our charging gun cable torsion test machine is professional laboratory testing equipment specifically developed for new energy electric vehicle charging connector manufacturers, third-party testing laboratories, and auto parts quality inspection centers. This EV cable torque torsion tester fully meets global mainstream EV charging certification standards. It is

AC Type 2 Charging Plug And DC CCS2 Charging Gun Comprehensive Testing System With Two Station This test system is designed for functional inspection of AC Type 2 and DC CCS2 charging connector cable assemblies. Each charging connector can be assigned an independent QR code, and all test results are automatically saved into reports for traceability. The system performs all required tests automatically in a single cycle, significantly improving efficiency and reducing labor

IEC 61851-1 Electric Vehicle Conductive Charging System IK Code Test Equipment IEC 61851-1 Electric Vehicle Conductive Charging System IK Code Test Equipment Applied Standards & Clauses IEC60068-2-75:2014 Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests IEC62262:2021 Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK code) IEC 61851-1-2017 Electric vehicle conductive charging system - Part 1: General

UL 2594 Cla.58 EV Charging Plug Drive-Over 4893N Test Equipment The test equipment is used to check whether a plug or vehicle connector shall have adequate resistance to damage from being driven over by a vehicle, unless it is provided with a cable management system which prevents the accessory from being left on the ground. Applied Standards & Clauses IEC 62196-1: 2022 clause 33 UL 2594:2016 clause 58 Test Principle IEC 62196-1:2022 clause 33: Accessories wired with the

IEC 61851-1 EV Charger Pendulum Impact Test Equipment Complete testing solution with pendulum and drop hammer impact methods for comprehensive mechanical strength evaluation. Product Overview The EV Charger IK Impact Test Equipment evaluates the mechanical strength and impact resistance of electric vehicle charging piles, enclosures, and electrical cabinets. It simulates real-world impact conditions using both pendulum hammer and vertical drop hammer methods. This advanced

IEC 62196-1 EV Plug Drive-Over Crushing Test Equipment The EV Plug Drive-Over Test Equipment is designed to evaluate the mechanical durability and safety of electric vehicle connectors and plugs under vehicle crushing conditions. This system simulates real-world scenarios where EV charging connectors may be accidentally run over by a vehicle, ensuring compliance with international safety standards. Engineered for precision and reliability, this equipment is widely used in EV

High And Low Temperature Bath Water Tank with both cooling and heating functions Product information: The low-high temperature bath is a high-precision thermostatic source with both cooling and heating functions, also serving as a compact chiller. It is widely used in fields such as petroleum, chemical, metallurgy, pharmaceuticals, biochemistry, material science, testing, chemical analysis, research institutions, universities, factory laboratories, and quality inspection and

BS1363-1 Screwless Terminals Thermal Stress Test For electrical and thermal stresses Test Product Overview: The test apparatus conforms to BS1363-1:2016+A1:2018 clause 25.1.1. It is used to check whether the screwless terminals can withstand the electrical and thermal stresses occurring in normal use. Technical parameters: Test Station Single Test Cycles 200 cycles, can be preset ON/OFF Time ON60min, OFF60min, can be preset Test Current AC 1~20A±(3%±1A) Temperature rise 2

IEC 62196-1 Test Plug Gauge Of Vehicle Connector Withdrawal Force Test Die Steel Product overview: The test plugs are required by IEC 62196-: 2022 clause 14.1.5, 14.1.6, according to the relevant standard sheets, shall have finely ground contacts of hardened steel, having a surface roughness not exceeding 0,8 µm over their active length and spaced at the nominal distances, with a tolerance of ±0,05 mm. The dimension of the plug contacts or the distance between contact

10KN Tensile Strength Test Machine With Computer Control Tensile Strength And Deformation Test Product information: This machine adopts computer control, widely used in the mechanical properties of various materials test, with special fixture is also suitable for all kinds of finished products tensile, compression, stripping, shear, tear, bending (folding) test. It can print a number of data, according to different data to make graphic output comparison, high control

IEC 62196-1 AC/DC Anti-Shock Probe Test Device for EV Connector Electrical Safety Testing Professional electrical safety testing equipment designed to verify protection against electric shock in electrical appliances, EV connectors, and charging equipment. The system works with standardized test probes to determine whether hazardous live parts can be contacted during accessibility tests. Product Information This equipment complies with IEC 62196-1:2022 requirements including