Other Flammability Tester

Melt Volume Flow Rate ASTM D1238 Melt Flow Rate Tester by Extrusion Plastometer Introduction: MFR ASTM D1238 Melt Flow Rate Tester is deisgned and manufactured according to ASTM D1238-98 and ISO1133; MFR ASTM D1238 Melt Flow Rate Tester is suitable for testing fluorine plastic, nylon and other engineering plastics, it is also used to test polyethylene (PE), polypropylene (PP), polyacetal (POM), polyphenylene ethylene (PS) ABS resin, polycarbonate and other plastics. Features:

Nft Hot Sale IEC60695 Insulation Material Needle Flame Tester​ Introduction: NFT Needle Flame Tester uses a Φ0.9mm needle burner, use butane as gas source, burn the specimen at 45 ° angle. Then according to the specimen is ignited and burned time and burning length to evaluate the fire hazard of the small flames caused by the fault condition inside the equipment. NFT Needle Flame Tester is widely used in low-voltage electrical equipment, household appliances, electrical

MFR ASTM D1238 Melt Flow Rates Tester Introduction: MFR ASTM D1238 Melt Flow Rate Tester is deisgned and manufactured according to ASTM D1238-98 and ISO1133; MFR ASTM D1238 Melt Flow Rate Tester is suitable for testing fluorine plastic, nylon and other engineering plastics, it is also used to test polyethylene (PE), polypropylene (PP), polyacetal (POM), polyphenylene ethylene (PS) ABS resin, polycarbonate and other plastics. Features: PLC control, LCD display, following

MFR ASTM D1238 Melt Flow Rates Tester Introduction: MFR ASTM D1238 Melt Flow Rate Tester is deisgned and manufactured according to ASTM D1238-98 and ISO1133; MFR ASTM D1238 Melt Flow Rate Tester is suitable for testing fluorine plastic, nylon and other engineering plastics, it is also used to test polyethylene (PE), polypropylene (PP), polyacetal (POM), polyphenylene ethylene (PS) ABS resin, polycarbonate and other plastics. Features: PLC control, LCD display, following

MFR ISO1133 Melt Volume Flow Rate and Melt Mass Flow Rates MFR Tester Introduction: MFR ISO1133 MVR and MFR Tester is deisgned and manufactured according to ASTM D1238-98 and ISO1133; MFR ISO1133 MVR and MFR Tester is suitable for testing fluorine plastic, nylon and other engineering plastics, it is also used to test polyethylene (PE), polypropylene (PP), polyacetal (POM), polyphenylene ethylene (PS) ABS resin, polycarbonate and other plastics. Features: PLC control, LCD

NPF-2 Fabrics NPFA 701 Small Scale Flammability Tester Introduction: NFPA 701 is Standard Methods of Fire Tests for Flame Propagation of Textiles and Films. According to different fabric weight, divided into 1 methods and methods 2.​​ Features: Specified apparatus for all hanging decorative materials weighing not less than 21 oz/yd² (700 g/m²). Stainless steel test cabinet with glass observation panel. 25° angle Bunsen burner with automatic timer to preset ignition time and

MFR Thermoplastics ASTM D1238 Melt Flow Rates Tester Introduction: MFR Thermoplastics ASTM D1238 Melt Flow Rates Tester is deisgned and manufactured according to ASTM D1238-98 and ISO1133; MFR Thermoplastics ASTM D1238 Melt Flow Rates Tester is suitable for testing fluorine plastic, nylon and other engineering plastics, it is also used to test polyethylene (PE), polypropylene (PP), polyacetal (POM), polyphenylene ethylene (PS) ABS resin, polycarbonate and other plastics.

TGA-I Plastic Material Thermo Gravimetric Analyzer TGA Introduction: Thermogravimetry (TG, TGA) is to observe the change of sample quality with temperature or time in the process of heating, constant temperature or cooling, so as to study the thermal stability and components of materials. TGA-I Plastic Material Thermo Gravimetric Analyzer TGA is widely used in research and development, process optimization and quality control of plastics, rubber, coatings, drugs, catalysts,

Insulating Material Glow Wire Tester ---- Model GWT Introduction: Electrical components or parts may reach very high temperature or even light the material nearby under failure or overload condition. Glow wire testing simulates thermal stress caused by glowing elements or overloaded resistors in short time, to evaluate the risk of fire. Glow wire test applies to electrical and electronic products, household appliance parts, plastic and non-metallic parts of insulating

Insulating Material Needle Flame Tester ---- Model NFT Introduction: NFT Needle Flame Tester uses a Φ0.9mm needle burner, use butane as gas source, burn the specimen at 45 ° angle. Then according to the specimen is ignited and burned time and burning length to evaluate the fire hazard of the small flames caused by the fault condition inside the equipment. NFT Needle Flame Tester is widely used in low-voltage electrical equipment, household appliances, electrical machines,

Building Material and Fitting Material Dripping Tester -- Model NF505 Introduction: The dripping test according to NF P 92-505 is a reaction to fire complementary test for M classification of building and fitting materials. It is used for thermal-melting materials for which some inflamed or not dripping, produced by a heating source, were noticed during the main test. This one can be either the electrical burner test for flexible and thin materials (NF P 92-503), or the