RF PCB Board

30mil AD1000 High Frequency PCB Double Sided RF PCB DK 10.2 PWB with Immersion Gold (Printed Circuit Boards are custom-made products, the picture and parameters shown are just for reference) Brief Introduction This type of immersion gold RF PCB is made on AD1000 material, PTFE/Woven Fiberglass/Ceramic Filled Laminate. The circuit board is dual layers with finished 1oz copper. No solder mask and silkscreen. Both layers are fully exposed to air. It’s 0.8mm thick and 50 boards

Rogers AD1000 Printed Circuit Board Arlon PTFE Ceramic-Filled High Frequency PCB Double Sided AD1000 RF PCB (Printed Circuit Boards are custom-made products, the picture and parameters shown are just for reference) Brief Introduction AD1000 is a high dielectric constant (10.2 or greater) high frequency material, a woven glass reinforced laminate. It permits circuit miniaturization, compared to traditional low loss materials and allows for greater dimensional stability and

30mil RF-45 High Frequency PCB with Blue Solder Mask Coating Immersion Silver on Pads (Printed Circuit Boards are custom-made products, the picture and parameters shown are just for reference) Brief Introduction This type of immersion silver RF PCB is made on one of Taconic’s ORCER family material: RF-45. The circuit board is dual layers with finished 1oz copper. Solder mask and silkscreen overlay are on top layer only. The bottom layer is fully exposed covered with immersion

RF-45 Low Loss RF PCB Stable DK High Frequency High Performance Circuit Board (Printed Circuit Boards are custom-made products, the picture and parameters shown are just for reference) Hi Everyone, Today, we’re going to talk about a type of Taconic ORCER Printed Circuit Board: RF-45 high frequency PCB. RF-45 is ceramic filled PTFE resin laminate utilizing woven fiberglass as reinforcement. It’s a kind of low loss laminate alternative to FR-4, dielectric constant (DK) flat

Rogers RO3006 RF Printed Circuit Board 2-Layer Rogers 3006 50mil 1.27mm Microwave PCB with Immersion Gold (Printed Circuit Boards are custom-made products, the picture and parameters shown are just for reference) Rogers RO3006 high frequency circuit materials are ceramic-filled PTFE composites intended for use in commercial microwave and RF applications. It was designed to offer exceptional electrical and mechanical stability at competitive prices. The mechanical properties

Rogers RO3006 High Frequency Printed Circuit Board 2-Layer Rogers 3006 10mil PCB DK6.15 DF 0.002 Microwave Gold PCB (Printed Circuit Boards are custom-made products, the picture and parameters shown are just for reference) Rogers RO3006 circuit materials are composite materials made of ceramic-filled PTFE, specifically designed for use in commercial microwave and RF applications. These materials offer excellent electrical and mechanical stability while remaining cost

Rogers PCB Made on RO3035 60mil 1.524mm DK3.5 With Immersion Gold for Remote Meter Readers (Printed Circuit Boards are custom-made products, the picture and parameters shown are just for reference) Rogers RO3035 high frequency circuit materials are ceramic-filled PTFE composites intended for use in commercial microwave and RF applications. It was designed to offer exceptional electrical and mechanical stability at competitive prices. The mechanical properties are consistent.

Rogers RO3035 30mil 0.762mm High Frequency PCB DK3.5 RF PCB for Datalink On Cable Systems (Printed Circuit Boards are custom-made products, the picture and parameters shown are just for reference) Rogers RO3035 high frequency circuit materials are ceramic-filled PTFE composites intended for use in commercial microwave and RF applications. It was designed to offer exceptional electrical and mechanical stability at competitive prices. The mechanical properties are consistent.

Rogers RO3003 Microwave PCB 2-Layer Rogers 3003 20mil Circuit Board DK3.0 DF 0.001 High Frequency PCB (Printed Circuit Boards are custom-made products, the picture and parameters shown are just for reference) Rogers RO3003 high frequency circuit materials are ceramic-filled PTFE composites intended for use in commercial microwave and RF applications. It was designed to offer exceptional electrical and mechanical stability at competitive prices. The mechanical properties are

Taconic Microwave PCB Made on TLF-35 30mil 0.762mm with OSP for Size Effective Antenna (Printed Circuit Boards are custom-made products, the picture and parameters shown are just for reference) TLF-35A is another type of low cost RF material. It's the best choice for low cost, high volume commercial microwave and radio frequency applications. TLF-35A has excellent peel strength for 1/2 ounce and 1 ounce copper (even in comparison to standard epoxy materials), a critical

TLX-7 62mil 1.575mm With Immersion Silver for Power Splitter (Printed Circuit Boards are custom-made products, the picture and parameters shown are just for reference) TLX offers reliability in a wide range of RF applications. This material is versatile due to its 2.45 - 2.65 DK range and available thicknesses and copper cladding. It is suitable for low layer count microwave designs. TLX is PTFE based fiberglass laminate, it is ideal for use in radar systems, mobile

Taconic High Frequency PCB Buitl on TLX-8 62mil 1.575mm with OSP for Directional Couplers (Printed Circuit Boards are custom-made products, the picture and parameters shown are just for reference) TLX offers reliability in a wide range of RF applications. This material is versatile due to its 2.45 - 2.65 DK range and available thicknesses and copper cladding. It is suitable for low layer count microwave designs. TLX is PTFE based fiberglass laminate, it is ideal for use in

Taconic High Frequency PCB Built On TLX-0 62mil 1.575mm With Immersion Silver for RF Antenna (Printed Circuit Boards are custom-made products, the picture and parameters shown are just for reference) TLX offers reliability in a wide range of RF applications. This material is versatile due to its 2.45 - 2.65 DK range and available thicknesses and copper cladding. It is suitable for low layer count microwave designs. TLX is PTFE based fiberglass laminate, it is ideal for use in

Today, I'd like to discuss a remarkable ceramic-filled PTFE composite that offers exceptional stability in both electrical and mechanical aspects. Rogers' RO3010 high frequency circuit laminates are specifically designed for commercial microwave and radio frequency applications. These laminates are made of ceramic-filled PTFE composites, which provide outstanding electrical properties and consistent mechanical properties. This allows our designers to create multilayer board

Hi, today we are happy to introduce the latest PCB from Bicheng Limited, the industry leader in high-quality printed circuit boards. This double-sided PCB is constructed with Rogers RO3010 material and a lead-free process, ensuring a reliable and environmentally-friendly product. With a working temperature range of -40℃ to +85℃, this PCB is designed to withstand extreme conditions. The board dimensions are 8.00 x 8.00 mm, with a minimum trace/space of 5/5 mils and a minimum

Looking for a high-performance 2-layer rigid PCB optimized for RF applications? This 2-layer rigid PCB is built with RF-10 copper clad laminates—a composite of ceramic-filled PTFE and woven fiberglass—designed to address the growing need for size reduction in RF applications while maintaining superior signal integrity. Engineered to IPC-Class 2 quality standards, this PCB delivers reliable performance for critical applications like microstrip patch antennas, GPS antennas, and

This PCB utilizes TP600 as its base material, adopts an Electroless Nickel Electroless Palladium Immersion Gold (ENEPIG) surface finish, and strictly complies with IPC-Class-2 quality criteria. Configured as a double-sided rigid structure with a 0.5mm (19.6 mil) TP600 substrate core, it is custom-engineered to satisfy the high-reliability and high-frequency performance demands of precision electronic systems, including satellite navigation and missile-borne devices. PCB

This PCB utilizes TP960 as its base material, features an Electroless Nickel Immersion Gold (ENIG) surface finish, and strictly adheres to IPC-Class-2 quality specifications. Designed as a double-sided rigid structure with a 0.5mm (19.6 mil) TP960 substrate core, it is tailored to meet the high-reliability and high-frequency performance criteria of precision electronic systems, such as global satellite navigation equipment and missile-borne platforms. PCB Specifications

This PCB utilizes WL-CT440 as its base material, incorporates an Immersion Gold surface finish, and strictly adheres to IPC-Class-2 quality specifications. Configured as a 2-layer rigid structure with a 0.254mm (10 mil) WL-CT440 substrate core, it is tailored to meet the high-frequency, low-loss performance requirements of aerospace, radar, and satellite communication systems. PCB Specifications Construction Parameter Specification Base Material WL-CT440 (hydrocarbon resin

0.6mm TLX-0 PCB Double-Sided Immersion Gold Finish This 2-layer rigid PCB caters to versatile RF and microwave applications, utilizing TLX-0—a PTFE fiberglass composite—to offer stable electrical performance and outstanding resilience in harsh environments (e.g., vibration, extreme temperatures, radiation). Every construction detail, from material selection to hole treatment, is optimized for low-layer-count microwave designs, ensuring reliability across use cases like radar