Flash Memory IC Chip

High-speed bidirectional passive switch for USB Type-C Alternate Mode. Supports 5 Gbps USB 3.1 Gen 1 and 5.4 Gbps DisplayPort 1.2a. Low power 0.6 mA active, 1 μA shutdown. Industrial temp range -40 to 85°C. Ideal for tablets, laptops, docking stations.

High-speed bidirectional passive switch supporting PCIe Gen III, USB3.1, and LVDS up to 10 Gbps. Features 7.5 GHz bandwidth, low insertion loss, and industrial temp range. Ideal for servers, backplanes, and industrial data switching with

High-speed CMOS analog multiplexer/demultiplexer with wide ±5V input range and low 7Ω typical ON resistance. Supports 2V to 6V control voltage and operates from -55°C to +125°C. Ideal for signal gating, factory automation, and sensors.

High-speed single bilateral analog switch IC operating from 1.65V to 5.5V. Features low ON-state resistance (5.5Ω typical at 4.5V), fast switching (0.5ns), and ESD protection. Ideal for signal routing in wireless, audio, and portable devices. Available in compact SC70-5 package.

Quad bidirectional translating switch for I2C/SMBus. Supports voltage-level translation between 1.8V to 5V buses. Low RON switches, hot insertion, and ESD protection. Ideal for servers, routers, and factory automation.

High-performance 4:1 analog multiplexer with 400 MHz bandwidth and 2200 V/μs slew rate. Ideal for video routing, HDTV, and instrumentation. Features 70 dB channel isolation, 0.02% differential gain error, and wide 6V to 12V supply range. Available in 14-pin SOIC package.

High-bandwidth USB 2.0 switch with 900 MHz bandwidth, 10 Ω max RON, and 8000-V HBM ESD protection. Supports partial power-down mode, low power consumption (1 μA max), and is ideal for portable electronics, industrial, and consumer applications. Available in compact UQFN and VSSOP packages.

Single-channel SPDT analog switch for 1.65V to 5.5V operation. Handles analog/digital signals with low ON-state resistance (6Ω) and high speed (0.5ns). ESD protected, latch-up resistant, ideal for IoT, audio, and portable devices.

Combines IEEE 802.3at PoE PD interface with current-mode DC-DC controller for isolated converters. Features 100V 0.7Ohm hotswap MOSFET, 15kV ESD protection, programmable frequency, and adapter ORing support. Ideal for VoIP, access points, and security cameras.

MAX3222CPWR is a 3V to 5.5V multichannel RS-232 interface IC with two drivers and two receivers. Features ±15kV ESD protection, low 1μA standby current, and operates up to 250kbps. Ideal for battery-powered systems, PDAs, and notebooks. Meets TIA/EIA-232-F standards.

Quad differential line receiver for RS-485/RS-422 with signaling rates exceeding 50 Mbps. Features 6 kV ESD protection, fail-safe on bus short/open/idle, wide common-mode range -7 V to 12 V, and low standby power

Robust RS-485 transceiver with ±16kV HBM and ±12kV IEC ESD protection. Operates from 5V supply at 250kbps. Features 60mV hysteresis,

Robust 3.3V RS-485 transceivers with ±15kV HBM ESD protection, wide -40°C to 125°C range, and low power consumption. Supports up to 200 nodes. Ideal for factory automation and telecom. Available in SOIC and VSSOP packages.

Integrated AISG v2.0 compliant transceiver with adjustable output power from 0dBm to +6dBm. Features wide input dynamic range, active bandpass filter at 2.176MHz, and low-power standby. Supports up to 115kbps signaling in a compact 3mm x 3mm QFN package.

The SN65HVD37DR is a 3.3V full-duplex RS-485 transceiver supporting up to 20 Mbps. Features low quiescent current, 15 kV HBM ESD protection, and 256-node bus capability. Ideal for industrial automation and telecom. Fully TIA-485-A compliant.

3.3V full-duplex RS-485 transceivers with 1/8 unit load for up to 256 nodes. Features 15-kV ESD protection, failsafe for bus idle/open/short, and low standby current

Low-power half-duplex RS-485 transceiver IC for industrial automation. Features 0.3mA active current, 15kV ESD protection, and supports up to 256 nodes. Ideal for energy meters, motor control, and building automation. Available in SOIC-8 package.

The SN65HVD235D is a 3.3V CAN transceiver supporting data rates up to 1 Mbps. Features ±36V fault protection, ±16 kV ESD, and low-current standby mode. Ideal for industrial automation, motor control, and CAN bus systems. ISO 11898-2 compliant.

The SN65HVD232D is a 3.3V CAN transceiver compliant with ISO 11898-2, supporting data rates up to 1 Mbps. Features include ±16 kV HBM ESD protection, up to 120 nodes per bus, thermal shutdown, and glitch-free hot plugging. Ideal for industrial automation, motor control, and CANopen networks.

High-speed CAN transceiver with improved EMC performance, replacing TJA1050. Supports up to 1 Mbps, features bus-fault protection from -27 V to 40 V, and meets ISO 11898-2. Ideal for industrial automation and automotive networks.