Flash Memory IC Chip

SN65DSI83 bridge converts MIPI DSI to FlatLink LVDS, supporting up to WUXGA 1920x1200 at 60 fps. Features 4 Gbps bandwidth, 25-154 MHz pixel clock, low power modes, and ESD protection. Ideal for tablets and notebooks. Operating temp -40°C to 85°C.

High-performance 4ch/4ch audio CODEC with 2-VRMS output, headphone amplifier, and six audio interface ports. Features THD+N 0.01%, SNR up to 100 dB, I2C control, and pop noise reduction. Ideal for digital TV and STB applications.

The PCA9557PWR is a remote 8-bit I/O expander for I2C and SMBus interfaces, operating from 2.3V to 5.5V. Features low 1μA standby current, 400kHz fast I2C bus, 5V-tolerant I/O, and high-current drive for LEDs. Supports up to eight devices on the bus with three address pins. Ideal for industrial and embedded systems.

Remote 16-bit I2C & SMBus I/O expander with low 1μA standby current. Features 5V-tolerant I/O, open-drain interrupt, and high-current drive for LEDs. Supports up to 8 devices via 3 address pins. Ideal for servers, routers, and industrial automation.

Texas Instruments PCA9536DGKR 4-bit I/O expander with I2C/SMBus interface. Features low 1μA standby current, 400kHz fast I2C bus, 5V tolerant I/O, and internal power-on reset. Ideal for remote GPIO expansion in industrial and embedded systems.

The PCA9515BDGKR is a dual bidirectional I2C bus and SMBus repeater supporting standard and fast modes up to 400kHz. It buffers SDA and SCL signals, extends bus capacitance to 400pF, and features 5.5V tolerant I/O, lockup-free operation, and ESD protection. Ideal for servers, routers, and industrial equipment.

Dual bidirectional I2C bus and SMBus repeater with active-high enable. Supports 2.3V to 3.6V operation, 400 kHz fast mode, and 400 pF bus capacitance. ESD and latch-up protected. Ideal for extending bus length or isolating bus segments.

MAX3243 UART interface IC operates from 3V to 5.5V supply, supports up to 250kbps data rate. Features ±15kV ESD protection, three drivers, five receivers, and auto-powerdown. Ideal for battery-powered systems, tablets, and laptops. Available in SSOP, SOIC, and TSSOP packages.

MAX3223EIPWR is a 3V to 5.5V RS-232 line driver/receiver with ±15kV ESD protection. Features two drivers, two receivers, low 1μA standby current, and auto-powerdown. Ideal for battery-powered systems, PDAs, and laptops.

Texas Instruments 20-bit transparent D-type latch with noninverting 3-state outputs. Features 25-Ω series resistors, hot insertion support, and flow-through architecture for optimized PCB layout. Ideal for buffer registers and I/O ports.

High-speed LVDS dual differential driver with 400 Mbps data rate, 3.3V operation, and 25 mW typical power dissipation. Meets TIA/EIA-644 standards, features 8 kV ESD protection, and supports cold sparing for high-reliability applications.

The SN65LVDS315RGER converts 8-bit parallel camera data to MIPI CSI-1 or SMIA CCP serial signals. Supports 3.5-27 MHz pixel clock, 1.8V core supply, and 1.8V-3.3V input range. Features three power modes, ESD >3 kV, and operates from -40°C to 85°C. Ideal for mobile phone camera interfaces.

High-speed LVDS interface ICs supporting signaling rates up to 630 Mbps for drivers and 400 Mbps for receivers. Operates from 2.4V to 3.6V supply with low power dissipation. Available in SOT-23 and SOIC packages. ESD protection exceeds 9 kV. Ideal for wireless and telecom infrastructure.

16-channel LVDS transceiver with 200Mbps receiver and 650Mbps transmitter speeds. Features 340mV differential output, integrated 110-ohm termination, and 12kV ESD protection. Supports simplex or half-duplex operation for reliable industrial communication.

Integrated transient voltage suppression and ±30kV ESD protection for robust industrial networks. Supports 128 nodes on bus with 250kbps data rate. Open-circuit fail-safe design and thermal shutdown. Ideal for utility meters and motor control.

3.3V RS-485 differential transceiver IC with 16kV HBM ESD protection, supports 1/10/32 Mbps signaling rates. Features bus short-circuit protection, failsafe receiver, and thermal shutdown. Ideal for industrial automation, motor control, and building networks.

8-bit I2C I/O expander for 2.5V to 6V operation. Features low standby current (10 μA max), open-drain interrupt, and high-current drive for LEDs. Ideal for servers, routers, and industrial automation. Compatible with most microcontrollers.

The MAX3232 is a low-power RS-232 interface IC with dual drivers and receivers, operating from 3V to 5.5V. Features ±15kV ESD protection, 250kbit/s data rate, and 300μA typical supply current. Ideal for battery-powered systems, PDAs, and laptops. Meets TIA/EIA-232-F standards.

Triple-channel digital isolator with iCoupler technology, offering up to 10 Mbps data rate and 3750V rms isolation. Low power consumption (1.7 mA/ch at 2 Mbps), high common-mode transient immunity >25 kV/μs, and RoHS-compliant SOIC-16 package. Ideal for SPI, RS-232/422/485, and industrial field bus isolation.

Triple-channel digital isolator based on iCoupler technology. Supports data rates up to 90 Mbps with 2500 Vrms isolation. Low power consumption, high common-mode transient immunity >25 kV/μs, and wide temperature range up to 125°C. Ideal for SPI, RS-232/422/485, and industrial field bus isolation. RoHS compliant.