High Strength And Narrow Distribution Wire Diamond Micron Powder
High Strength Narrow Distribution Wire Diamond Powder 5um To 60um
Description:
It is made of high grade and high strength diamond as raw material, on the basis of conventional diamond powder technology, by carrying out special treatment for the crystal shape and surface purification, particles have features of very clean surface, high toughness, consistent crystal shape, good thermal stability and wear resistance. Through our unique technology of critical oversize elimination and length/width ratio control, the particles also have strictly concentrated PSD, and very high content of effective grinding grits. Besides, a variety of coated products are available, it greatly enhances the retention between diamond particles and the bond, thus to prolong the tool's life and improve the sharpness. It also facilitates heat dissipation within the bond system resulting in longer service life of products.
Micron Size Available for Grade HID-WD (μm)
| 4-6 | 4-8 | 5-10 | 6-12 | 8-12 |
| 8-16 | 10-15 | 10-20 | 12-22 | 15-25 |
| 20-30 | 22-36 | 30-40 | 40-50 | 50-60 |
Particle Size Distribution Specification for Superabrasive Grains
| Size | D10≥(µm) | D50(µm) | D95≤(µm) | Max(µm) | Min(µm) |
| 0-0.25 | 0.1 | 0.170~0.210 | 0.38 | -- | -- |
| 0-0.5 | 0.12 | 0.220~0.280 | 0.51 | --- | -- |
| 0-1 | 0.42 | 0.501~0.580 | 0.795 | 1.156 | 0.375 |
| 0.5-1 | 0.472 | 0.581~0.690 | 1.053 | 1.375 | 0.375 |
| 0.5-1.5 | 0.504 | 0.691~0.871 | 1.298 | 1.945 | 0.375 |
| 0-2 | 0.62 | 0.872~0.985 | 1.542 | 2.312 | 0.446 |
| 1/2 | 0.761 | 0.986~1.224 | 1.894 | 3.27 | 0.63 |
| 0.5-3 | 0.94 | 1.225~1.487 | 2.401 | 3.889 | 0.63 |
| 1/3 | 1.048 | 1.488~1.712 | 2.882 | 4.625 | 0.75 |
| 1.5-3 | 1.169 | 1.713~2.014 | 3.321 | 5.5 | 0.75 |
| 2/3 | 1.392 | 2.015~2.302 | 3.663 | 6.541 | 0.892 |
| 2/4 | 1.644 | 2.303~2.754 | 4.496 | 7.778 | 0.892 |
| 2/5 | 1.803 | 2.755~3.312 | 5.5 | 9.25 | 1.06 |
| 3/6 | 2.448 | 3.313~3.898 | 6.386 | 11 | 1.499 |
| 3/7 | 2.913 | 3.899~4.676 | 7.566 | 13.08 | 1.783 |
| 4/8 | 3.605 | 4.677~5.400 | 8.455 | 15.56 | 2.121 |
| 4/9 | 3.952 | 5.401~6.062 | 9.762 | 18.5 | 2.522 |
| 5/10 | 4.401 | 6.063~6.700 | 10.98 | 18.5 | 2.999 |
| 5/12 | 5.022 | 6.701~7.673 | 12.95 | 22 | 3.566 |
| 6/12 | 5.807 | 7.674~8.549 | 13.97 | 26.16 | 4.241 |
| 7/14 | 6.411 | 8.550~9.483 | 15.13 | 26.16 | 4.241 |
| 8/16 | 7.113 | 9.484~10.78 | 17.82 | 31.11 | 5.044 |
| 8/20 | 8.102 | 10.79~12.56 | 20.6 | 37 | 5.998 |
| 10/20 | 9.186 | 12.57~14.18 | 22.54 | 37 | 7.133 |
| 12/22 | 10.53 | 14.19~16.05 | 24.41 | 44 | 7.133 |
| 12/25 | 12.01 | 16.06~17.65 | 26.61 | 44 | 8.482 |
| 15-25 | 13.32 | 17.66~19.55 | 29.75 | 52.33 | 10.09 |
| 20-30 | 15.04 | 19.56~22.50 | 34.64 | 62.23 | 12 |
| 22-36 | 17.28 | 22.51~26.12 | 39.98 | 74 | 12 |
| 30-40 | 20.11 | 26.13~30.10 | 46.56 | 88 | 14.27 |
| 30-50 | 22.36 | 30.11~34.58 | 52.87 | 88 | 16.96 |
| 36-54 | 25.68 | 34.59~39.00 | 60.94 | 104.7 | 20.17 |
| 40-60 | 29.45 | 39.01~43.20 | 69.86 | 124.5 | 20.17 |
| 50-70 | 32.42 | 43.21~47.50 | 72.65 | 124.5 | 23.99 |
| 54-80 | 36.56 | 47.51~52.50 | 80.74 | 124.5 | 23.99 |
Feature:
- Sharp and blocky crystal shape
- Very clean and purified diamond surface (below 20PPM)
- Concentrated PSD
- High content of effective grinding grits
For the particle shape of diamond powder, it is better to use approximately spherical particles and an equal area shape during polishing. In the micropowder standard, needle-shaped particles refer to the ratio of the major axis to the minor axis exceeding 3:1. Needle-rod-shaped particles exceeding the maximum particle size cannot be contained in the micropowder, but needle-rod-shaped particles with a length between the maximum nominal size and the largest particle are allowed not to exceed 3%.
Observed under a microscope through light transmission, they are transparent flake particles, and those with a size smaller than D5 can be disregarded. The flake particles in fine diamond powder do not exceed 5%.
Characteristics:
With our raw materials all from strictly quality-controlled suppliers, we pay more attention to all kinds of product standards to meet various application requirements from customers, such as: basic multiple edge particle feature, above international standard, basic particle contents at upper and lower limits, oversize control, low magnetic, hight surface purify.
Application for Wire Diamond Micron Powder Grade HID WD:
It is designed for producing diamond wire, and it is also widely used for cutting, grinding and polishing hard and brittle materials such as monocrystalline silicon, polycrystalline silicon, sapphire, quartz, semiconductor, liquid crystal glass, magnetic materials, etc.
Get in Touch
Have questions about our products or want to discuss a custom order? Our team is ready to help you.